CHAPTER 11__________
PLACARDS AND MARKINGS
TABLE OF CONTENTS_________________
SUBJECT_______ Markings of the Lavatory Units. Markings of the Lavatory Doors Markings of the Attendant Call and Reading-Light-Switch Panel CH/SE/SU________ C_ PAGE EFFECTIVITY____ ___________13 106-149, 151-199 201-299,13 106-149, 151-199 201-299,44 106-149, 151-199201-299,
11-CONTENTS Page 13 Aug 01/05
CES
PLACARDS AND MARKINGS - GENERAL - DESCRIPTION AND OPERATION___________________________________________________________
R R R R R R R R 1. General_______ This document shows the placards, stencils and markings and gives their location on the aircraft. This chapter has the parts that follows: - Placards and markings on the external side of the aircraft (Ref. ATA 11-20) - Placards and markings on the internal side of the aircraft (Ref. ATA 11-30). There are three types of placards and markings ATA 100 specification.
R R R A. Safety Data These placards and markings are used for the flight crew, and passenger cabins, and for equipment safety. They include WARNINGS and CAUTIONS.
R R B. Maintenance Data These are servicing and maintenance instructions.
R R R C. By Local Regulation The aircraft must have these placards and markings. When these types of placards are shown in Chapter 11, they are identified by (1).
2. Labels______
A. General
(1) Standard type No.1 label
(2) Standard type No.2 label
(3) FOTOFOIL type No.3 Standard No.1 and 2 labels are in plastic material with white letters on black matt finish. Type No.3 labels are in 0.076 mm (0.002 in.) metal foil for use in skydrol zones with white letters on black matt finish.
B. Dimensions (Ref. Fig. 001)
3. Label Replacement_________________ This chapter gives the replacement procedure of the different types of labels: - Decals - Nameplates (For example on circuit breaker panel) - Identification bands on metal lines - Labels on heat-resistant ducting
EFF : ALL
11-00-00Page 1
Nov 01/04 CES
Dimensions of the Labels
Figure 001
EFF : ALL 11-00-00 Page 2
Feb 01/98
CES
-Labels on laminations
-ESSO labels
-SSO (SCOTCHCAL) labels
-FOTOFOIL labels
-BSB (DUROFIX) labels
-Metal identification plates
-Labels on landing gear
-Engine leasing plate
NOTE : This list does not include all the labels installed on the aircraft.
____ The installation or replacement of labels or instruction placards attached by different types of threaded fasteners or rivets is not given below since no special procedure is necessary.
EFF : ALL
11-00-00Page 3
Nov 01/04
R
CES
PLACARDS AND MARKINGS - GENERAL - MAINTENANCE PRACTICES
_______________________________________________________
R TASK 11-00-00-000-002
R Removal of the Decals
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS_______
R ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R 1. Reason for the Job__________________
R Self Explanatory
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific abrasive cloth, grade 240
R No specific masking paper
R No specific masking tape
R B. Consumable Materials
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. 19-003 USA AMS 3819
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM PLACARDS AND MARKINGS(13)