曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
VSD HSD MMS COMM
RAPID
RAPID
IDM INDEX PAGE
AIR REQ
ARTY REQ
MOVEMENT
REPORTS
RCVD MSG
START
STATUS
MSGS/FTXT
AIR REQ LIST 1/3
1 N/G A/READY
2 ILLUM B/ACPTD
2 MLFR C/SHOT
/DELTD NEW
/DELTD NEW
/DELTD NEW
AIR MISSION REQUEST LIST PAGE 1-3
AIR MISSION TYPE SELECT PAGE
AIR MSN TYPE
HELLFIRE
RAPID
406530-47-2
J0855
VSD
OTHER ORDNANCE
NO PREF
continue.
Figure 4-78. Air Request Pages
4-158
TM 1-1520-248-10
8. IDM switch Press to return to IDM Index
page.
9. ARTY REQ key Press.
10. PPLN LIST key Press.
11. P1 or P2 Press NEW as desired.
12. L-2 Press on Preplan Insertion pages.
13. Repeat steps 1 through 12 to insert a second
preplanned mission.
NOTE
If the PPLN mission is requested as M1, it
can only be stored as P1.
4-139. NEW ARTILLERY FIRE MISSION
REQUEST.
To initiate a new fire mission, proceed as follows:
1. Target locate steps Accomplish as
required.
2. IDM switch Press as required to display
IDM Index page.
3. ARTY REQ key Press.
4. NEW key opposite mission (M1 or M2) to be
replaced Press.
5. Mission type Press applicable key and
enter required parameters on subsequent
pages until all data is inserted.
6. Review mission on Summary page and make
changes as required.
7. SEND key Press.
NOTE
• New Artillery Fire Mission Request
(simplified) is depicted in fig. 4-80.
• A generic Artillery Mission Summary page
PULL
MAN
PULL
BKUP
BRT
C
ONT
VSD HSD MMS COMM
PULL
MAN
PULL
BKUP
BRT
C
ONT
HSD MMS COMM
PULL
MAN
PULL
BKUP
BRT
C
ONT
VSD HSD MMS COMM
RAPID
RAPID
406530-47-3
J0855
AIR MISSION ROUNDS ENTRY PAGE
ROUNDS - #
N/G
RQST
RQSTD
XMT?
1SGL LOA/D
N/G-TGT
105SFQ12345678
SEND
AIR MISSION SUMMARY
AIR MISSION SUMMARY PAGE
XMT
FIRE CONTROL
TGT TYPE
OWN RNG/BRG
TO TGT
SEND
DESTINATION TGT NO/TYPE
ACFT/
TGT
ANGLE
MISSION CMD
MISSION STATUS
SEPARATION ANGLE
OR TIME ON TGT
RAPID
VSD
DEST - ?? ??:1
is shown in fig. 4-81. Figure 4-79. Air Mission Summary Pages
4-159
TM 1-1520-248-10
4-140. COPPERHEAD FIRE MISSION communication. In addition, the Movement pages allow
ACTIVE AND PREPLANNED. automatic transmission of current position through MY
POSITION key and free text communication through
To accomplish a Copperhead fire mission, proceed as the OTHER key.
follows (fig. 4-82).
1. Target locate steps Accomplish. 4 - 1 4 2 . M O V E M E N T C O M M A N D
TRANSMISSION.
2. IDM switch Press as required to display
Transmit movement commands as follows (fig. 4-83):
IDM Index page.
1. IDM switch Press as required to display
3. ARTY REQ key Press.
IDM Index page.
4. To accomplish in active mission, M1 or M2
2. MOVEMENT key Press.
key Press as desired.
3. Appropriate movement type key Press.
5. CPHD Press.
4. Appropriate destination select key Press.
NOTE
NOTE
If KNPT TGT is selected, entry of two-digit
KNPT number is required.
Pressing OTHER key will display Freetext
Message Entry page where a manual entry
6. NEW TGT or KNPT TGT Select as
can be made using MFK.
appropriate.
5. Mission Summary page Review and
7. ARTY Mission Summary page will appear change as required.
Review ARTY Mission Summary page and
change as required.
6. SEND key Press (fig. 4-83).
8. SEND key Press (fig. 4-80).
4-143. REPORT COMMUNICATIONS.
4 - 1 4 1 . M O V E M E N T C O M M A N D The Reports pages (fig. 4-84) allow the observer to
COMMUNICATIONS. provide various information to team and net members
such as: Situation/status (SIT/STATUS) which reports
The Movement pages allow position instructions to be the observers own situation, SPOT which reports target
transmitted without voice communication. The IDM activity, ATI to provide intelligence reports to artillery
operator can issue directions to specific or all team units, BDA to report battle damage assessments, CAS
members to MOVE TO, HOLD AT, rendezvous (RDZV) to report casualty assessments, NEG SPOT, and
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPTER 2(7)
