曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
PREAMBLE and enter time.
8. MSGS Press to access Message Preset
(2) On Monitor page Select MONITOR
Entry pages 1-6. Press L-3 to activate
and enter time, or select OFF.
keyboard. Enter free text message up to 36
characters in length. Six preset messages
f. AUTH Select MANUAL or NONE. may be set up. Formulate messages and
page through as needed. (MFD defaults to
g. Paging key Press to go to next page. Start page 2/2 when exiting page 6/6).
4-277
TM 1-1520-248-10
9. MVMT Press to access 6 each Movement a. To enter or select a preplanned request:
Preset Entry pages. Press L-2 and/or L-3 on (1) Select ATHS switch (accesses ATHS
each Preset page to enable keyboard. Enter Top Menu page).
up to 15 characters per line. Formulate (2) Select ARTY REQ (selects Artillery
messages and page through as needed. Mission pages).
(Operator defaults to Start page 2/2 when (3) Select NEW Next to present mission
exiting page 6/6). to be replaced.
(4) Select REQ PPLN Choose preplan
10. Select ATHS switch Then select Start page mode.
1/2. (5) Select FPF or CPHD (Only one FPF
allowed).
a. CURR NET Enter CURRENT NET (6) ARTY Summary page appears... Press
number. SEND.
(7) Preplanned MTO from FDC accepts
b. ORIG Enter ORIGIN (Originator’s) PPLN request.
identifier. (8) Select ATHS switch.
(9) Select ARTY REQ.
c. TEAM Enter TEAM identifier. (10) Select PPLN LIST.
(11) Press NEW P1 or P2 to designate the
d. BDCST Enter BROADCAST identifier. desired preplanned mission number.
(12) Press L-2 to insert PPLN request.
NOTE
b. To enter a second preplanned request
If helicopter is equipped with EGI, time of repeat all of the previous steps listed in a.
day is automatically input by GPS. above.
e. TIME Enter TIME using 24 hour format. 2. NEW ARTY FIRE MSN RQST.
11. BULK Press to access Bulk Data Summary a. Locate target using MMS for automatic entry
page. of coordinates.
On Bulk Data Summary page: b. Select ATHS switch.
a. Enter Destination ID by pressing L-1 and c. Select ARTY REQ.
specifying subscribers ID on MFK.
d. Select NEW (Next to mission to be
b. Press L-2 to access Bulk Data Select page. replaced).
Making a selection causes a default back to
Bulk Data Summary page. e. Mission Type Select NEW TGT, KNPT
TGT, QUICK, REQ PPLN, ILLUM, or CPHD.
c. SEND; then scroll to next page by pressing
L-3. Utilize the “SCROLL-SEND” procedure f. TARGET TYPE Select one of 17 targets.
until all desired data has been sent.
g. Select TARGET STRENGTH.
d. CMPLT. Send CMPLT message when
finished with bulk data transmission. h. Select TARGET ACTIVITY.
4-225. ARTILLERY REQUEST.
1. PREPLANNED (FPF & CPHD Only)
4-278
TM 1-1520-248-10
a. Locate target using MMS.
i. ...TARGET MOVING direction automatically
selected if TARGET ACTIVITY was selected b. Select ATHS switch.
as MOVING.
c. Select AIR REQ.
j. ...If MOVING, then enter speed in kph using (1) AIR REQUEST List page Select
MFK. Mission 1 through 8 from AIR REQ List
(pages 1-3) by pressing NEW.
k. Review/Change Mission Summary page. (2) On MSN TYPE page Select REMOTE
HLFR, AMC/TGT, AMC, ORD, WR/TGT,
l. SEND key Press. or WR/ORD.
(3) Make appropriate selections as needed.
NOTE (4) Review/Change Mission Summary page.
A Copperhead is fired from an artillery 155 d. To execute an Immediate Fire Request,
MM gun. Press SEND while on the Summary page.
(Mission will also be stored at this time).
3. COPPERHEAD Fire Mission (Active and
Preplanned). e. To enter other missions, proceed to step 1
above.
a. Locate target using MMS.
2. Recalling a stored AIR MISSION:
b. Select ATHS switch.
a. Select ATHS switch.
c. Select ARTY REQ.
b. Select AIR REQ.
d. Select NEW (Next to mission to be
replaced). c. Select desired mission number (1-8) from
pages 1, 2, or 3.
e. Select CPHD.
d. Review/Change Mission Summary page.
f. Select STRENGTH (number of Copperheads
to be fired). e. SEND key Press.
g. TARGET POSITION Select NEW or NOTE
KNPT.
HELLFIRE missiles are normally fired from
h. Review/Change Mission Summary page. aircraft.
i. SEND key Press. 3. REMOTE HELLFIRE request.
4. Selection of ILLUM and QUICK Artillery a. Select ATHS switch.
Mission types follow the same procedures as
in step 3. above except a KNPT where, after b. Select AIR REQ.
specifying known point number, send
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPTER 2(50)
