曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
3. INIT−DB/DF. This is the initial HOG window 4-90).
displayed on the CPG MFD. First four lines of
data, described below, identify the databases 8. XX TACID. This page provides a list of
currently stored in nonvolatile memory (NVM) TACIDs assigned to this network. Selection of
(fig. 4-90). desired identifier displays the XX CONFIG
window with the new selection. This selection
LOAD DB − loads database currently stored in defines operators TACID for the given
NVM. network.
RETAIN CURRENT − retains data currently stored
in NVM and identified on the first lines of HOG 9. INIT-PASSWD. Successful entry of a
display.
LOAD DFLTS − loads a different set of Target password without appended characters gives
Type, Target Qty, and Nature of Operations access to unclassified data. For classified
default selections. This procedure is normally only access, appropriate appended characters
done once per theater of operation and requires must be added to password. Successful entry
entry of a password established at AMPS. of password displays INIT-INPROG window.
4-185
TM 1-1520-248-10
Figure 4-90. IDM Initialization Thread (Sheet 1 of 3)
4-186
TM 1-1520-248-10
Figure 4-90. IDM Initialization Thread (Sheet 2 of 3)
4-187
TM 1-1520-248-10
Figure 4-90. IDM Initialization Thread (Sheet 3 of 3)
4-188
TM 1-1520-248-10
maintenance of current position, weapon status, and
aircraft status of all team members.
4-172. TACFIRE START-UP.
After IDM initialization, pressing the IDM switch on
CPG auxiliary panel displays TACFIRE page most
recently accessed (fig. 4-92). Pressing IDM switch
again displays TACFIRE Index page (fig. 4-93).
Pressing any mode key, except MMS, removes the
TACFIRE Page display. Pressing the MMS MODE key
displays TACFIRE MMS Page.
a. Rapid Function (L-5). Legend is either RAPID
or STORE. Pressing L-5 when legend is RAPID sends
a RAPID control command to the IDM, causing the
RAPID page to be displayed. If IDM detects display
characteristics containing a UTM coordinate, legend is
changed to STORE. Pressing L-5 when legend is
STORE causes any UTM coordinate contained on lines
1 through 4 to be stored to the Target List. Targets are
stored in order from line 1 to line 4. Last coordinate
stored is also added to Prepoint List in manual position.
The RAPID function provides direct access to any one
of the following five operational IDM pages.
Figure 4-91. HOG Start Menu Summary Page of Highest Priority Received
Message
10. INIT-INPROG. Indicates IDM i s being Airborne Mission Summary Page
configured as specified during initialization Artillery Mission Summary Page
process. Completion of initialization process Mayday Message Summary Page
is indicated by display of HOG START Quick Menu Page.
window (Fig. 4-91). Refer to TACFIRE
STARTUP or JVMF paragraphs for specific b. Send Function (R-5). SEND is only displayed at
procedures. R-5 when IDM indicates a SEND condition is valid. If
SEND condition is valid, pressing R-5 causes a SEND
4-171. TACFIRE OVERVIEW. command to be initiated.
The IDM provides the capability to maintain current c. MMS TACFIRE Page. If MMS FORWARD,
mission status for up to eight active airborne fire PREPOINT, or SEARCH page is displayed on CPG
missions, two active artillery fire missions, and two MFD when IDM switch is activated, TACFIRE MMS
preplanned artillery fire missions. The unit retains all page is displayed. This page can also be accessed by
mission essential data in nonvolatile storage and can pressing MMS mode key on any TACFIRE page. This
store up to 12 previously received messages for later page is identical to a TACFIRE page except, MMS
recall. The system also provides the capability to video is present and firing of laser is allowed. The
request and execute airborne fire missions specifying following data can be displayed on a TACFIRE MMS
either HELLFIRE or standard ordnance and request page:
and provide the required coordination to execute a
remote HELLFIRE mission. The aircrew can also MMS Rotary Advisories.
request and execute artillery fire missions as Forward MMS Line of Sight.
Artillery Aerial Observer (FAAO); transmit spot MMS Mode Status.
situation, battle damage assessments, and casualty HELLFIRE Time of Flight.
reports. Team leader capabilities allow for receiving TV/TIS Zoom Level.
and handing over fire requests to the best weapon MMS Azimuth and Elevation display.
systems available to execute the mission; commanding Heading Tape.
of team/unit movement with preset parameters; Lubber Line.
retention of lists of preplanned battle positions, FARP Bearing-To-Waypoint Arrow.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPTER 2(16)
