曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
the data entered in meters to feet. System previously used numeric identifier is used,
does not assume zeros. Each digit must be its coordinates are replaced by the newly
entered up to four digits (five digits for feet entered coordinates.
entry).
9. ELEV key Press. System is activated to 4. WPT DES key Press and enter as
accept new elevation. required.
10. Elevation Enter on MFK. Elevation will 5. POS key Press and enter as required.
display in ELEV block as typed.
NOTE
11. ENTER key Press. Elevation in meters will
be entered into memory.
If different grid zone is to be used, enter the
alphanumeric identifier on the MFK using
12. MANUAL align Select and press as two numeric characters and one alpha
desired. character, then press ENTER.
13. FAST align Select and press as desired.
6. ELEV key Press and enter as required.
NOTE
7. STORE key Press. Waypoint is entered in
If fast align is to be used, the aircraft’s last list. Subsequent waypoints are entered in
present position must be stored immediately similar manner.
3-90
TM 1-1520-248-10
3-77. CHANGING EXISTING WAYPOINT 12. ENTER key Press. Location is placed into
DATA. memory and placed on waypoint list.
1. HSD key Press. HSD page will display. 13. ENTER key Press. Variation is placed into
memory and placed on waypoint list.
2. WPT LIST key Press. WPT LIST page will
display. 3-78. ENTERING WAYPOINT INTO FLIGHT
PLAN. 3. NEW WPT key Press. NEW WAYPOINT
page will display.
1. HSD key Press. HSD page will display.
4. WPT DES key Press. System is activated
2. FPLN key Press. FLIGHT PLAN page will
to accept desired waypoint designator.
display.
5. Waypoint designator Enter waypoint to be
3. ADD LEG key Press to enter waypoint.
changed on MFK. Identifier will display in
WPT DES block as typed.
4. ADD LEG key Press again to enter
NOTE subsequent waypoints.
For ease of data entry, it is only necessary 5. Procedure complete Select MFD page
to enter the one- or two-digit numeric desired for flight.
portion of the designator to recall stored
waypoint data. 3-79. ROTORCRAFT MAPPING SYSTEM
(RMS) DISPLAY PAGES.
6. ENTER key Press. System is set to accept
new coordinates for waypoint designator. NOTE
NOTE The VIDEO SYM INTEN MFD switch on the
MMS control panel will adjust overlay legend
Only data to be changed needs to be display from black to white.
entered by proceeding to the appropriate
instructions below. If the waypoint elevation RMS is a real time digital map system and provides the
is to be changed, the POS data need not be ability to display map data with selected display
altered. features. The RMS includes a dedicated circuit card
within the Right Master Controller Processor Unit (R
7. POS key Press. If position information is to MCPU), a Map Data Unit (MDU) and four RMS display
be changed. Cursor will display to the right of pages. The system uses data generated with the
grid zone identifier of POS block. aviation mission planning station (AMPS) and stored on
the data transfer module (DTM). It includes the
8. Eight digit coordinates Enter on MFK using capability to overlay symbology as well as elevation
two alpha and eight numeric characters. bands over the digital map image and provides for
Coordinates will display in POS block as moving map displays complete with waypoints, targets,
typed. battlefield graphics, cultural features, flight plan maps,
and other mission data. The RMS display pages are
9. ENTER key Press. Location is entered into activated from the HSD page (figure 3-37), the Map
memory and entered on waypoint list. Offset page (figure 3-41), or the Direct Waypoint page
(figure 3-43). Refer to figure 3-47 for a flow chart of the
10. ELEV key Press. If elevation information is RMS pages. There are four RMS display pages: the
to be changed. Cursor will display to the right RMS Page, Normal Mode (figure 3-48), the RMS Page,
of ELEV. SLEW Mode (figure 3-49), the RMS Setup Page (figure
3-50), and the RMS Feature Selection Page (figure 3-
11. Waypoint elevation Enter in meters on 51).
MFK. Elevation will display in ELEV block as
typed.
3-91
TM 1-1520-248-10
RMS FEATURE
SELECTION PAGE
HSD PAGE MAP OFFSET PAGE
RMS SETUP PAGE
R5
R5
R5
L4
R5
L3
R4
L4
B B B
DIRECT WAYPOINT
PAGE
RMS PAGE, NORMAL MODE RMS PAGE, SLEW MODE
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
TECHNICAL MANUAL OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPT(82)
