曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
center of the LOAD MISSION page if data
c. Transmit/receive authentication codes and loading is unsuccessful.
line number.
4. LOAD MISSION (1, 2, 3) keys Press as
d. Current net assignments. required to display LOAD MISSION 1, 2, or 3
e. Authentication subscriber data. page (fig. 4-23).
15. For weapons: 5. Select desired mission load data.
4-47
TM 1-1520-248-10
6. LOAD key Press to initiate loading. NOTE
d. DTS (MDU) Mission Storing.
• (CDS2) If the ISP fails, ADSS is not
NOTE available.
STORE FAIL will display if data storing is • If the MCPUs fail, ADSS is not
unsuccessful. available.
c. ADSS Controls and Functions. The system is
1. STORE DATA IN MISSION 1, 2, OR 3 keys controlled by MFD keys and cyclic switches. See fig. 4-
Press as required to display STORE 26 for test pattern and fig. 4-27, 4-28, and 4-29 for
MISSION 2 page (fig. 4-24). controls and functions.
2. Select desired mission store data.
WARNING
3. STORE key Press to initiate store.
4. MFK Enter required identifier for selected If the -903 version of the ODA is being
stored data keys. used, failure to remove ANVIS neck cord
prior to operation of ADSS may prevent
egress from the aircraft in an emergency.
4-37. NOTEBOOK.
d. ADSS Operation.
The NOTEBOOK page presents the aircrew with an
additional scratchpad for data entry and information 1. INIT button Press. INITIAL PAGE 1
display. The NOTEBOOK page (fig. 4-25) is accessed displays.
by pressing the L-5 NOTEBOOK key on the INITIAL
PAGE 1. With the manipulations of a data edit bar and
cursor, lines of text are entered, deleted, or inserted 2. PAGE 2 key Press. INITIAL PAGE 2
into a field display by MFK or ground station. The edit displays.
bar and cursor are positioned using the line address
keys along the left side of the MFD. The NOTEBOOK 3. Pilot cyclic ODA switch Press to activate
permits entry of 44 characters on 10 lines of text on 20 ADSS ODA display. CPG ODA is activated by
pages. default.
4 - 3 8 . A N V I S D I S P L A Y SYMBOLOGY 4. ADSS ODA TEST key Press. Test pattern
displays in ODA. Check all lines of test SUBSYSTEM. pattern display. An absent line indicates ODA
The ANVIS Display Symbology Subsystem (ADSS) display failure.
provides the pilot and CPG wearing night vision
devices with VSD displays superimposed on the real 5. ADSS ODA TEST key Press to delete test
world imagery. pattern.
a. (CDS2) ADSS Description. The ADSS consists NOTE
of ISP drive electronics and two Optical Display
Assemblies (ODA) which mount on ANVIS night vision
devices. ADSS provides three modes of VSD displays: P i l o t ODA display brightness can be
Normal, Hover, and Hover Bob-up. controlled with the ADSS brightness select
switch located on pilot cyclic. Successive
b. ADSS Description. The ADSS consists of presses of this switch cycle pilot ODA from
MCPU drive electronics and two Optical Display OFF, to preset brightness, to maximum
Assemblies (ODA) which mount on ANVIS night vision brightness, to OFF. The preset brightness
devices. ADSS provides three modes of VSD displays: level is the level indicated and adjusted on
Normal, Hover, and Hover Bob-up. INITIAL PAGE 2.
4-48
TM 1-1520-248-10
PULL
MAN
PULL
BKUP
BRT
C
ONT
VSD HSD MMS COMM
2
1
3
4
5
LOAD MISSION
C505
6
7
8
LOAD MISSION
ABCD-1
LOAD MISSION
8701
DL TRANSFER
STORE DATA
IN MISSION 1
STORE DATA
IN MISSION 2
STORE DATA
IN MISSION 3
INIT PAGE 1
C7 A4
INIT PAGE 2
406075-606
J1145
CONTROL/INDICATOR FUNCTION
1. STORE DATA IN MISSION 1 Calls up STORE MISSION 1 page.
key
2. STORE DATA IN MISSION 2 Calls up STORE MISSION 2 page.
key
3. STORE DATA IN MISSION 3 Calls up STORE MISSION 3 page.
key
4. INIT PAGE 1 key Calls up INITIAL PAGE 1.
5. INIT PAGE 2 key Calls up INITIAL PAGE 2.
6. LOAD MISSION key Calls up LOAD MISSION 3 page.
7. LOAD MISSION key Calls up LOAD MISSION 2 page.
8. LOAD MISSION key Calls up LOAD MISSION 1 page.
Figure 4-22. DL TRANSFER Page
4-49
TM 1-1520-248-10
CONTROL/INDICATOR FUNCTION
1. (CDS2) ATHS key Selects/deselects ATHS data for loading.
IDM key Selects/deselects IDM data for loading.
2. LASER CODES key Selects/deselects laser data for loading.
3. WEAPONS DATA key Selects/deselects WEAPONS data for loading.
4. DATA LOADER TRANSFER key Selects/deselects DATA LOADER TRANSFER page.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
TECHNICAL MANUAL OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPT(106)
