曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
authentication table line will be displayed.
To change, press key and enter desired
line.
c. RCV LINE Current receive authentication
table line will be displayed. To change,
press key and enter desired line using MFK.
d. MODE key Press once to activate
authentication tables. Press again to scroll
among XMT, BOTH or RCV.
e. TABLE key Press to access transmit or
receive table index.
(1) Select desired transmit table line.
(2) Press key adjacent to line number.
Enter transmit authentication code from
SOI.
(3) Paging key Press to sequence to
Start page.
8. MSGS key If desired, press to access
Message Present Entry pages. Press paging
key as required to return to Start page.
9. MVMT key If desired, press to access Figure 4-67. ATHS Initialization Pages
Preset Movement Message pages. Enter
4-124
TM 1-1520-248-10
movement commands on subpages. Press Request list, selecting air mission type, entering the
paging key as required to return to Start required parameters, receiving the summary, and
page. transmitting the data.
10. Select ATHS Press. Then select Start b. Types of air missions are as follows:
page 1/2. (1) Remote HELLFIRE wherein the number of
rounds to be fired is requested and guidance is by
a. CURR NET key Enter current net other than the launching element.
number.
(2) At My Command/Target (AMC/TGT) wherein
b. ORIG key Enter subscriber identifier. the target type and strength is defined for the firing
element. The firing element determines ordnance to be
c. TEAM key Enter team number. fired on the requestor’s command.
(3) At My Command/Ordnance (AMC/ORD)
d. BC key Enter broadcast number. wherein ordnance type and number of rounds are
specified to the firing element by the observer and is to
NOTE be fired upon command of the observer.
Time of day is automatically input by GPS. (4) When Ready/Target (WR/TGT) wherein the
target type and strength is given to the firing element
e. TIME key Enter current time of day. which then fires choice of ordnance when ready.
(5) When Ready/Ordnance (WR/ORD) wherein
11. BULK key Press if it is desired to upload the type of ordnance and suggested number of rounds
another operator ATHS. Select BULK on Start are specified by the observer and are to be fired by the
page 2. firing element when ready.
a. Enter Destination ID by pressing L-1.
4-97. STORING OR EXECUTING AIR MISSION
b. Press L-2 to access Bulk Data Select page. FIRE REQUEST.
Making a selection causes a default back to
Bulk Data Summary page. To store or execute an air mission fire request, proceed
as follows:
c. SEND; then scroll to next page. Utilize the
SCROLL-SEND procedure until all desired 1. Target locate steps Accomplish as
data has been sent. required.
d. COMPLT Send CMPLT message when 2. ATHS switch Press as required to display
finished with bulk data transmission. ATHS Top Menu page.
3. AIR REQ key Press.
4-96. AIR REQUEST PAGES.
4. Line (1-8) Select mission number on which
a. Description. The Air Request (AIR REQ) list mission is to be entered. NEW key Press.
can store up to eight fire mission requests. The three
Index pages display observer mission number, type of 5. MSN TYPE Press appropriate key.
ordnance, firing element (subscriber) to which request
was sent, and mission status. This list is for originating 6. As pages sequence, press appropriate key to
mission requests. Incoming new missions are stored in input desired mission.
the Received Message file. Stepping through the
mission list is accomplished by pressing the paging 7. Air Mission Summary page Review and
(upper right) key on the MFD. Accessing a stored Air change parameters as required.
Mission Request Summary page is accomplished by
pressing the left key adjacent to desired mission. To execute an immediate fire request, proceed as
Complete mission information will display. Initiating a follows:
new mission request is accomplished by pressing a
NEW key of an available mission number on the Air
4-125
TM 1-1520-248-10
8. On Air Mission Summary page, SEND key
Press.
9. ATHS switch Press and repeat steps 1
through 8 above for each net as required.
To recall and send a stored mission, proceed as
follows:
1. ATHS switch Press as required to display
ATHS Top Menu page.
2. AIR REQ key Press.
3. Desired mission (1-8) line number Select.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
TECHNICAL MANUAL OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPT(131)
