曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
4. On Air Mission Summary page, SEND key
Press.
a. Remote HELLFIRE (REMOTE HLFR)
mission request. The paging required for a
simplified request is depicted in fig. 4-68.
b. The Mission Status w i l l change from
REQUESTED to ACCEPTED, READY,
FIRE, and SHOT. At completion of mission
an END OF MISSION message should be
sent.
c. A generic Air Mission Summary page is
shown in fig. 4-69.
4-98. ARTILLERY REQUEST PAGES.
a. Description. The mission data contained in the
ATHS is formatted to be consistent with the TACFIRE
Artillery Fire Direction Center (FDC) system and
associated forward observer digital message devices
(DMD). Artillery mission command selection is initially
entered on the ARTY Mission Summary page
automatically as REQ. Upon receipt of the TACFIRE
FDC message-to-observer (MTO), the mission
command will automatically change to FIRE. A READY
command will be displayed if the Battery Computer
System (BCS) is online with TACFIRE. Target position
(range and bearing from the helicopter) is automatically
calculated. By pressing the TGT PSN (target position)
key, the operator can manually enter the UTM grid,
range, bearing, and altitude of the target on subpages
if required.
The Artillery Request List stores two active artillery
missions and two preplanned mission requests on the
Preplanned Mission List subpage. Accessing either
active mission is accomplished by pressing the M1 or
M2 key on the ARTY REQ List page. To review a Figure 4-68. Air Request Pages
preplanned mission, pressing the PPLN LIST key on
4-126
TM 1-1520-248-10
the Preplanned Mission List page will cause the
Preplanned Mission Summary page to display.
NOTE
In order to store a preplanned mission, a
preplan request must be executed and
stored as a standard artillery preplan
request. Then the mission must be inserted
into preplan list.
I n i t i a t i n g a new a r t i l l e r y m i s s i o n r e q u e s t i s
accomplished by pressing the NEW key of an available
mission number, selecting artillery mission type,
following prompts through the subpages, reviewing
Summary page, and transmitting data.
b. Types of artillery mission requests are as follows:
(1) NEW TGT wherein the observer defines
target type and strength.
(2) Known Point (KNPT) wherein the observer
defines a point which is a location previously identified
and numbered, known both to the requestor and to the
artillery FDC. The requestor then provides target type
and strength.
(3) QUICK wherein the requestor enters only a
known point. All other data is known by the artillery
FDC.
(4) Preplanned (PPLN) wherein the observer
provides type of fire request (either Final Protective
Fire (FPF) or Copperhead (CPHD) guided munitions).
Only one FPF can be preplanned at a time; however,
both preplanned missions can be Copperhead. The
requestor then provides target position and known point
number.
(5) Illumination (ILLUM) wherein the observer
provides target position and known point number.
Included in this mission type is the ability for the
observer to format a coordinated mission by using both
active mission (M1 and M2) files.
(6) Copperhead (CPHD) wherein the target
position is defined as NEW or Known Point and point
number is provided to the firing element.
4-99. PREPLANNED FIRE REQUESTS.
To insert a preplanned fire request, proceed as follows:
1. ATHS switch Press as required to display
ATHS Top Menu page.
2. ARTY REQ key Press. Figure 4-69. Air Mission Summary Pages
4-127
TM 1-1520-248-10
6. Review mission on Summary page and make
3. On line opposite mission to be replaced. changes as required.
NEW key Press.
4. PPLN request key Press. 7. SEND key Press.
5. Mission type Select either FPF or CPHD 8. New A r t i l l e r y F i r e M i s s i o n Request
as desired. (simplified) is depicted in fig. 4-70.
6. Target position or known point number 9. A generic Artillery Mission Summary page is
Enter as appropriate.
shown in fig. 4-71.
7. ARTY Mission Summary page will appear
Press SEND. Wait for preplanned MTO then continue. 4-101. COPPERHEAD FIRE MISSION
ACTIVE AND PREPLANNED.
8. ATHS switch Press to return to ATHS Top
Menu page. To accomplish a Copperhead fire mission, proceed as
follows (fig. 4-70).
9. ARTY REQ key Press.
1. Target locate steps Accomplish.
10. PPLN LIST key Press.
11. P1 or P2 Press NEW as desired. 2. ATHS switch Press as required to display
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
TECHNICAL MANUAL OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPT(132)
