曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Hazard Avoidance voidance voidance
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
Displaying weather on the Weather Radar Page:
1) Select the Weather Radar Page in the Map Page Group with the FMS Knob.
2) Select the MODE Softkey.
3) While on the ground, select the STANDBY Softkey. A one-minute warm-up period is initiated (countdown is displayed on the screen). After the warm-up is complete, the radar enters the Standby Mode.
a) Select the WEATHER Softkey. A confirmation window is displayed.
Figure 6-46 Confirming Activating Radar
b) Turn the small FMS Knob to highlight YES and press the ENT Key to continue radar activation.
OR:
If the aircraft is airborne, select the WEATHER Softkey. A one-minute warm-up period is initiated (countdown is displayed on the screen). After the warm-up is complete, the radar begins transmitting.
4) Turn the RANGE Knob to select the desired map range.
5) The horizontal scan is initially displayed (Figure 6-45). If desired, select the VERTICAL Softkey to change to vertical scanning.
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 323
Hazard Avoidance voidance voidance
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
Vertically scanning a storm cell: NOTE: Vertical scanning of a storm cell should be done with the aircraft wings level to avoid constant adjustment of the Bearing Line.
1) While in the Horizontal Scan view, select the BRG Softkey. This places the cursor in the BEARING field and displays the Bearing Line.
If the Bearing Line is not displayed, press the MENU Key and turn the large FMS Knob to select Show Bearing Line. Press the ENT Key.
2) Press the ENT Key.
3) Turn the small FMS Knob to place the Bearing Line on the desired storm cell or other area to be vertically scanned.
Figure 6-47 Bearing Line on Horizontal ScanBearing LineScan Line
4) Select the VERTICAL Softkey. A vertical scan of the selected area is now displayed (Figure 6-48).
5) The small FMS Knob may be used to move the scanned bearing line a few degrees right or left.
6) Turn the RANGE Knob to adjust the range.
7) Press the FMS Knob to remove the cursor.
8) To select a new area to be vertically scanned, select the HORIZON Softkey to return to the Horizontal Scan view and repeat the previous steps.
The RANGE Knob can also be used to adjust bearing from left to right.
324 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
Hazard Avoidance voidance voidance
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
Figure 6-48 Vertical Scan Display
A
d
justing Antenna Tilt Angle
In order to make an accurate interpretation of a storm cell, the radar beam should be pointed at the wet part of the weather cell to record the proper rainfall intensity (color level). The ideal aiming point is just below the freezing level of the storm. The best way to find this point is to use the Vertical Scan feature. The antenna tilt angle can be centered on the strongest return area in the vertical scan to get a more accurate view of the coverage and intensity of the target in the horizontal scan.
Adjusting antenna tilt on the Horizontal Scan display:
1) Press the FMS Knob to activate the cursor in the TILT field.
2) Turn the small FMS Knob to select the desired antenna tilt angle.
3) Press the ENT Key.
4) Press the FMS Knob to remove the cursor.
The RANGE Knob can also be used to adjust tilt up and down.
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 325
Hazard Avoidance voidance voidance
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
Adjusting antenna tilt on the Vertical Scan display:
1) Select the TILT Softkey to activate the cursor in the TILT field and display the Tilt Line.
If the Tilt Line is not displayed, press the MENU Key and turn the large FMS Knob to select Show Tilt Line. Press the ENT Key.
2) Turn the small FMS Knob to adjust the antenna tilt angle. The selected tilt angle is implemented when Horizontal Scan is again selected.
The RANGE Knob can also be used to adjust tilt.
Figure 6-49 Adjusting Tilt on Vertical Scan DisplayScan LineTilt Line
326 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cessna Citation Mustang Pilot’Guide 2(14)
