(b)
P6, Main Power Distribution Panel
1) 6B34, WINDOW HEAT 1L PWR
2) 6B17, WINDOW HEAT 1R PWR
(c)
P180, DC Power Distribution Panel
1) 180H26, WDO HEAT CONT 1L
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-44-02
ALL ú ú 02 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
SEE A
WASHER
SEE C SEE B ON L-WINDSHIELD-R
PILOT'S OVERHEAD PANEL
A
SOLENOID LEFT VALVE FAIRING MOUNTING BOLT A (SINGLE HOLE) WASHER JET
VALVE RIGHT SOLENOID WASHER CONTAINER FLUID NOZZLE FAIRING NOZZLE THREADS RETAINING ADJUSTMENT SCREWS O-RINGS PLATE
AIRPLANE SKIN
PUMP B DRIP TRAY NOZZLE FAIRING SEALANT NOZZLE FITTING VALVE CHECK A FLUID WASHER
C
PLATE
Windshield Washer Nozzle Components Installation Figure 401 A-A
K27151
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-44-02
ALL ú ú 02 Page 402 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
2) 180H12, WDO HEAT CONT 1R
S 034-003
(2)
Remove the mounting screw from the nozzle fairing and remove the fairing.
S 164-004
(3)
Remove the sealant from the fairing and the plate.
S 114-005
(4)
Clean the surfaces of the nozzle fairing and the plate with solvent.
S 024-006
(5)
Remove the nozzle:
(a)
Loosen the three adjustment screws at the bottom of the nozzle.
(b)
Turn the nozzle assembly counterclockwise by hand to remove it from the fitting attached to the airplane structure.
(c)
Remove the nozzle assembly. Discard the 2 O-rings.
TASK 30-44-02-404-007
3. Nozzle Installation (Fig. 401)___________________
A. Consumable Materials
(1)
G00507, Cloth - Lint Free (to clean the nozzle fitting)
(2)
A00247, Sealant - BMS 5-95, Class B
(3)
B00184, Solvent - BMS 11-7
B. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AIPC 30-43-01, Fig. 1
(3)
SSM 30-42-01
(4)
WDM 30-43-11
C. Access
(1) Location Zone 221 Control Cabin, LH - Outside No. 1 Left Window 222 Control Cabin, RH - Outside No. 1 Right Window
D. Procedure
S 424-008
(1) Install the nozzle:
(a)
Clean the fluid out of the nozzle fitting with a lint-free cloth.
(b)
Make the new O-rings wet with water and install them on the nozzle shaft and the nozzle fitting.
(c)
Use your hand to turn the nozzle assembly clockwise 6 to 7 turns in the fitting.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-44-02
ALL ú ú 02 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(d) (e) Point the nozzle approximately toward the center of the No. 1 window.Turn the three alignment screws clockwise until they touch the plate (do not tighten them).
(2) S 864-009Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) P7, Overhead Circuit Breaker Panel 1) 7E26, WSHLD WASH
(3) S 864-010Supply electrical power (AMM 24-22-00/201).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 防冰和排雨 ICE AND RAIN PROTECTION(77)
