曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
to the engine when set to CUTOFF. The mixture lever attaches to the control quadrant in the
center console. The mixture lever is the right hand lever in the control quadrant.
The mixture control lever has a lock-out lever attached. The lock-out lever prevents accidental
movement of the mixture control lever. The spring loaded lock-out lever engages in a toothed
rack. The toothed rack attaches to the tubular spacers at the right of the control quadrant.
A bowden cable connects between the mixture lever in the cockpit and the mixture control-lever
at the engine. The bowden-cable wire-end attaches to the mixture lever through a hole in a
swivel fitting. A screw locks it in position. A bracket holds the inboard end of the swivel fitting.
Two rivets attach the bracket to the mixture lever. The outer sheath of the bowden cable has a
threaded end fitting. Two nuts attach the end fitting to a tab on the side of the control quadrant.
The bowden cable goes from the center console up, behind the instrument panel and through
the firewall to the engine bay. A feed-thru fitting holds the cable in position at the firewall. A fire
resistant compound seals the bowden cable where it goes through the firewall. From the firewall
the bowden cable goes through a rubber grommet in the aft baffle on the left hand side.
On aircraft equipped with a standard fuel pump, the outer sheath of the mixture control bowden
cable has a threaded end that attaches to a bracket at the apron with two nuts, which can be
used to adjust the range of movement of the mixture control lever. The bowden-cable wire-end
attaches to the fuel-mixture control-lever of the fuel pump through a hole in the attachment bolt.
You can adjust the length of the wire at this point to set the correct fuel mixture control position.
On aircraft equipped with an altitude compensating fuel pump, the mixture cable has a notched
swivel termination at the engine end. The notch slides onto the mixture support bracket, which is
fastened to the apron. A keeper is bolted to the bracket to secure the bowden cable. There is a
rod-end attached to the end of the bowden cable that connects the mixture control cable to the
fuel mixture lever by a bolt.
Engine Controls
DA20-C1 AMM
Page 4
24 Mar 1999 76-00-00 Doc # DA201-C1
Rev. 1
C. Alternate Air
The alternate air control opens a by-pass for the engine air filter if it becomes blocked with debris
or ice. The alternate air lever attaches to the control quadrant in the center console. The
alternate air lever is the left hand lever in the control quadrant.
A bowden cable connects between the alternate air lever in the cockpit and the lever at the airbox.
The bowden-cable wire-end attaches to the alternate air lever through a hole in a swivel
fitting. A screw locks it in position. A small bracket holds the inboard end of the swivel fitting.
Two rivets attach the bracket to the alternate air lever.
The outer sheath of the bowden cable has a threaded end fitting. The end fitting attaches to a
tab bent from the side of the quadrant.
The bowden cable goes from the center console, up behind the instrument panel and through
the firewall to the engine bay. A feed-thru fitting holds the cable in position at the firewall. A fire
resistant compound seals the bowden cable where it goes through the firewall.
From the firewall the bowden cable goes below the engine on the left side. The outer sheath of
the bowden cable then attaches to the support bracket at the air intake. You can adjust the
range of movement of the alternate air lever at this position. The eye-end of the bowden-cable
attaches to the alternate air lever with a bolt, nut, two washers and a return spring. You can
adjust the length of the wire at this point to set the correct Alternate air valve position.
D. Friction Adjuster
The friction adjuster adjusts the force necessary to move the three control levers in the throttle
quadrant. The friction-adjuster control-knob is on the right hand side of the center console.
Nylon washers and 4 spring washers attached to the lever axis adjust the friction when they are
compressed or released. To increase the friction on the control levers, turn the control knob
clockwise. To decrease the friction on the control levers, turn the control knob counter-clockwise.
DA20-C1 AMM
Engine Controls
Doc # DA201-C1
Rev. 0 76-00-00 Page 101
19 Dec 1997
TROUBLE-SHOOTING
1. General
Use the data below to trouble-shoot the engine controls. See also the Teledyne Continental Motors
Maintenance Manual for the IO-240-B engine.
Complaint Possible Cause Remedy
Engine will not start. Mixture controls not correctly
adjusted.
Do a range of movement
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石20系列AMM 2(94)
