曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
CAUTION: YOU MUST ATTACH CAPS TO HOLES/PIPES WHEN YOU
DISCONNECT THEM. IF YOU DO NOT DO THIS, CONTAMINATION
CAN ENTER THE HOLES/PIPES. THIS CAN CAUSE BLOCKAGE
TO THE AIRPLANE SYSTEMS.
(8) Disconnect these items and pull them
carefully through the aft baffle:
− The throttle control cable.
− Mixture control cable.
− Fuel pressure hose from the fuel
manifold valve.
− Fuel drain pipe from the fuel distribution
manifold.
− Oil breather hose at the oil separator.
− 4 ignition harness cables.
Refer to Chapter 76-00
Refer to Chapter 76-00
Attach blanks to all pipes/hoses and fuel/oil
units.
(9) Disconnect the oil-cooler flexible pipe at the
aft baffle.
− Remove the worm drive clamp.
(10) Remove the LH and RH baffles:
− Remove the two screws, spacers and
washers from the RH baffle that supports
the two heat shield brackets.
− Remove the three screws and plain
washers from the RH baffle.
− Remove the five screws and washers
from the LH baffle.
Move the heat-shield clear.
Two screws at the rear of the baffle and
one at the front of the baffle.
Two screws at the side of the baffle. Two
screws at the rear of the baffle and one at
the front of the baffle.
DA20-C1 AMM
Air
Doc # DA201-C1
Rev. 10 75-00-00 Page 205
23 Jun 2004
Detail Steps/Work Items Key Items
(11) Remove the LH and RH aft baffles.
− Remove the three screws and washers
from the LH aft bracket.
− Remove the three screws and washers
from RH aft bracket.
(12) Remove the aft baffle:
− Remove the two screws and plain
washers that attach the aft baffle to the
inter-cylinder brackets.
(13) Disconnect the two electrical connectors
from the generator and carefully push them
through the apron.
(14) Remove the apron:
− Remove the screw two washers and nut
that attach the bracket for the induction
manifold flexible pipe.
− Remove the two screws and washers
that attach the apron to the inter-cylinder
support brackets.
Air
DA20-C1 AMM
Page 206
23 Jun 2004 75-00-00 Doc # DA201-C1
Rev. 10
B. Install The Baffles
Detail Steps/Work Items Key Items
(1) Install the apron:
− Install the two screws and washers that
attach the apron to the inter-cylinder
support brackets.
− Install the screw two washers and nut
that attach the bracket for the induction
manifold flexible pipe.
− Tighten the screws.
(2) Connect the two electrical connectors to the
generator:
− Carefully put the generator electrical
cables through the rubber grommet in
the apron.
− Attach the main electrical supply cable to
the generator.
− Attach the plain washer, spring washer
and nut to the stud.
− Tighten the nut and pull the rubber boot
over the connection
− Install the electrical (indication)
connector to the generator.
(3) Install the RH baffle:
− Attach the two screws, spacers and
washers to the two heat shield brackets
and the RH baffle.
− Install the two screws into the cylinder
heads.
− Tighten the screws.
DA20-C1 AMM
Air
Doc # DA201-C1
Rev. 10 75-00-00 Page 207
23 Jun 2004
Detail Steps/Work Items Key Items
(4) Install the LH baffle:
− Attach the two screws and washers to
the LH baffle.
− Install the two screws into the cylinder
heads.
− Tighten the screws.
(5) Install the two screws and washers into the
apron where it attaches to the RH and LH
baffles:
− Tighten the screws.
(6) Install the LH aft baffle:
− Install the two screws and plain washers
that attach to the LH baffle .
− Tighten the screws.
(7) Install the RH aft baffle:
− Install the two screws and plain washers
that attach to the RH baffle.
− Tighten the screws.
(8) Install the aft baffle:
− Attach the two screws and washers that
attach the aft baffle to the inter-cylinder
brackets.
− Tighten the screws.
− Attach the three screws and washers to
the RH aft baffle that attach to the aft
baffle.
− Tighten the screws.
− Attach the three screws and washers to
the LH aft baffle that attach to the aft
baffle.
− Tighten the screws.
(9) Connect the oil-cooler flexible pipe to the aft
baffle.
Install the worm drive clamp.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石20系列AMM 2(91)
