曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
position.
The bottom left screw on the front of the
taxi/landing light assembly is the adjusting
screw.
Refer to Figure: 2
(3) Do an operational test of the taxi/landing
light.
− Set the GEN/BAT switch to ON.
− Set the LANDING/TAXI/MAP circuit
breaker to closed.
− Set the taxi/landing light switch to ON.
(4) Install the taxi/landing light cover to the wing.
DA20-C1 AMM
Lights
Doc # DA201-C1
Rev. 0 33-40-00 Page 205
19 Dec 1997
5. Replace A Bulb In The Wing Tip
A. Replace A Position Light Bulb In The Wing Tip
Detail Steps/Work Items Key Items
(1) Set the GEN/BAT switch to OFF.
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE YOU WAIT
FOR A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON
THE ANTI COLLISION LIGHTS. THE POWER SUPPLIES TO THE
ANTI COLLISION LIGHTS GENERATE HIGH VOLTAGE. HIGH
VOLTAGE CAN CAUSE DEATH OR INJURY TO PERSONS.
(2) Remove the light unit cover from the wing tip
and the lamp glass.
Refer to Figure: 1
(3) Replace the bulb. Refer to Figure: 1
(4) Install the lamp glass and the light unit cover.
(5) Do an operational test of the position light.
6. Remove/Install The Light Unit In The Wing Tip
A. Remove The Light Unit In The Wing Tip
Detail Steps/Work Items Key Items
(1) Set the GEN/BAT switch to OFF.
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE YOU WAIT
FOR A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON
THE ANTI COLLISION LIGHTS. THE POWER SUPPLIES TO THE
ANTI COLLISION LIGHTS GENERATE HIGH VOLTAGE. HIGH
VOLTAGE CAN CAUSE DEATH OR INJURY TO PERSONS.
(2) Remove the light unit cover and the lamp
glasses from the wing tip.
Refer to Figure: 1
(3) Remove the 3 light bulbs. Refer to Figure: 1
Lights
DA20-C1 AMM
Page 206
19 Dec 1997 33-40-00 Doc # DA201-C1
Rev. 0
Detail Steps/Work Items Key Items
(4) Remove the screws that attach the light unit
to the wing tip.
− Carefully move the light unit out from the
wing tip.
− Disconnect the two electrical
connections from the rear of the light
unit.
− Remove the light unit.
B. Install The Light Unit In The Wing Tip
Detail Steps/Work Items Key Items
(1) Put the light unit in position at the wing tip.
− Connect the two electrical connectors to
the rear of the light unit.
(2) Install the screws that attach the light unit to
the wing tip.
(3) Install the three bulbs to the light unit.
WARNING: DO NOT OPERATE THE ANTI-COLLISION LIGHTS WHEN
PERSONS ARE CLOSE TO THE AIRPLANE. AND DO NOT LOOK
DIRECTLY AT THE LIGHT WHEN IT OPERATES. ANTI-COLLISION
LIGHTS CAN CAUSE EYE DAMAGE.
(4) Do an operational test of the position lights.
− Set the GEN/BAT switch to ON.
− Set the POSITION/STROBE circuit
breakers to closed.
− Set the position/strobe light switches to
ON.
DA20-C1 AMM
Lights
Doc # DA201-C1
Rev. 0 33-40-00 Page 207
19 Dec 1997
Detail Steps/Work Items Key Items
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE YOU WAIT
FOR A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON
THE ANTI COLLISION LIGHTS. THE POWER SUPPLIES TO THE
ANTI COLLISION LIGHTS GENERATE HIGH VOLTAGE. HIGH
VOLTAGE CAN CAUSE DEATH OR INJURY TO PERSONS.
(5) Set the GEN/BAT switch to OFF.
(6) Wait for a minimum of five minutes.
Install the three lamp glasses and the light
unit cover.
7. Remove/Install The Power Unit For The Anti-Collision Lights
A. Remove The Power Unit For The Anti-Collision Lights
Detail Steps/Work Items Key Items
(1) Disconnect the airplane battery. Refer to Chapter 24-31
(2) Remove the left pilots seat. Refer to Chapter 25-10
(3) Disconnect the wiring harness from the
power unit.
(4) Remove the four nuts that attach the power
unit to the fuselage.
− Remove the power unit.
B. Install The Power Unit For The Anti-Collision Lights
Detail Steps/Work Items Key Items
(1) Put the power unit in position and install the
four nuts that attach the power unit to the
fuselage.
(2) Connect the wiring harness to the power
unit.
(3) Connect the airplane battery. Refer to Chapter 24-31
Lights
DA20-C1 AMM
Page 208
19 Dec 1997 33-40-00 Doc # DA201-C1
Rev. 0
Detail Steps/Work Items Key Items
WARNING: DO NOT OPERATE THE ANTI-COLLISION LIGHTS WHEN
PERSONS ARE CLOSE TO THE AIRPLANE. AND DO NOT LOOK
DIRECTLY AT THE LIGHT WHEN IT OPERATES. ANTI-COLLISION
LIGHTS CAN CAUSE EYE DAMAGE.
(4) Do an operational test of the position lights.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石20系列AMM 2(15)
