曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
the mounting bracket.
(4) Remove the filter.
(5) Put the new filter in position on the mounting
bracket.
(6) Install the nut which attaches the filter to the
mounting bracket.
(7) Remove the caps from the hose ends.
Connect the 2 flexible hoses to the vacuum
filter.
(8) Do an engine run-up.
− Refer to the DA20-C1 Flight Manual.
Do a test for correct operation of the
vacuum system.
(9) Install the instrument panel cover. Refer to Chapter 25-10
Vacuum
DA20-C1 AMM
Page 204
29 Apr 2004 37-10-00 Doc # DA201-C1
Rev. 9
5. Adjust the Vacuum Regulator
Detail Steps/Work Items Key Items
(1) Do a ground run-up.
− Refer to the DA20-C1 Flight Manual.
(2) Make a note of the vacuum value.
(3) If necessary, adjust the vacuum regulator:
− Adjust regulator under right hand side of
instrument panel
The vacuum must be 4.8 - 5.4 in.Hg at
1800 RPM.
On the bottom of the regulator.
Monitor the vacuum value.
(4) Shut down the engine.
DA20-C1 AMM
Vacuum
Doc # DA201-C1
Rev. 0 37-20-00 Page 1
19 Dec 1997
CHAPTER 37-20
VACUUM INDICATING
1. General
See Chapter 37-00 for the system description and operation. This section gives you the troubleshooting
and maintenance procedures for the vacuum indicating system.
Vacuum
DA20-C1 AMM
Page 2
19 Dec 1997 37-20-00 Doc # DA201-C1
Rev. 0
Figure 1: Vacuum Indicator Installation
DA20-C1 AMM
Vacuum
Doc # DA201-C1
Rev. 0 37-20-00 Page 101
19 Dec 1997
TROUBLE-SHOOTING
1. General
Use the data below to trouble-shoot the vacuum indicating system.
Complaint Possible Cause Remedy
Vacuum gauge shows no
vacuum. Vacuum operated
instruments operate correctly.
Vacuum gauge defective. Replace the vacuum gauge.
Vacuum
DA20-C1 AMM
Page 102
19 Dec 1997 37-20-00 Doc # DA201-C1
Rev. 0
Intentionally left blank
DA20-C1 AMM
Vacuum
Doc # DA201-C1
Rev. 0 37-20-00 Page 201
19 Dec 1997
MAINTENANCE PRACTICES
1. General
These maintenance practices tell you how to remove and install the vacuum gauge. See Chapter
37-00 for the system description. See Chapter 37-10 for the vacuum distribution system
installation.
2. Remove/Install the Vacuum Gauge
A. Remove the Vacuum Gauge
Detail Steps/Work Items Key Items
(1) Remove the instrument panel cover. Refer to Chapter 25-10
(2) Release the flexible hoses to the vacuum
gauge.
− Put caps on the hose ends
(3) Release the bezel nut which attaches the
gauge to the instrument panel.
(4) Remove the gauge from the instrument
panel.
B. Install the Vacuum Gauge
Detail Steps/Work Items Key Items
(1) Put the vacuum gauge in position in the
instrument panel.
(2) Install the bezel nut which attaches the
gauge.
(3) Remove the caps from the hose ends.
Connect the flexible hoses to the vacuum
gauge..
(4) Install the instrument panel cover. Refer to Chapter 71-10
(5) Do an engine run-up. Refer to Chapter 71-00
Do a test for correct operation of the
vacuum system. If necessary, adjust the
system.
Vacuum
DA20-C1 AMM
Page 202
19 Dec 1997 37-20-00 Doc # DA201-C1
Rev. 0
Intentionally left blank
DA20-C1 AMM
Standard Practices
And Structures
Doc # DA201-C1
Rev. 0 51-TITLE Page 1
19 Dec 1997
CHAPTER 51
STANDARD PRACTICES AND
STRUCTURES
Standard Practices
And Structures
DA20-C1 AMM
Page 2
19 Dec 1997 51-TITLE Doc # DA201-C1
Rev. 0
Intentionally left blank
DA20-C1 AMM
Standard Practices
And Structures
Doc # DA201-C1
Rev. 14 51-CONTENTS Page 1
30 Oct 2008
TABLE OF CONTENTS
CHAPTER 51-00 STANDARD PRACTICES AND STRUCTURES..........................................................1
1. General.......................................................................................................................1
2. Structural Classification..............................................................................................1
3. Design Dimensions, Clearances And Wear Limits.....................................................3
4. The Description And Location Of Parts......................................................................3
5. Repair Limitations.......................................................................................................5
6. Inspection Techniques ...............................................................................................5
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石20系列AMM 2(42)
