31.7Pressurization ........................... 340
FAR23.841:Pressurized cabins. . . . . . . . . . . . . . . . . 340 FAR23.843:Pressurizationtests. . . . . . . . . . . . . . . . 341
31.8FireProtection . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
FAR23.851:Fireextinguishers. . . . . . . . . . . . . . . . . 342
FAR23.853:[Passengerand crewcompartmentinteriors.] . . 342
FAR23.855:[Cargoandbaggagecompartment .reprotection.]344
FAR 23.859 : Combustion heater .re protection. . . . . . . . 344
FAR 23.863 : Flammable .uid .re protection. . . . . . . . . . 346
FAR23.865 :Fireprotectionof .ight controls,enginemounts,
and other.ightstructure.. . . . . . . . . . . . . . . 347
31.9 Electrical Bonding and Lightning Protection . . . . . . . . . 347
FAR23.867 :[Electricalbonding andprotection againstlight-ning and staticelectricity.] . . . . . . . . . . . . . . 347
31.10Miscellaneous. . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
FAR23.871:[Leveling means.] ................. 347
′
Elodie Roux. Septembre 2003
Subpart D : Design and Construction
FAR 23.601 : General.
The suitability of eachquestionabledesigndetail andparthaving animportantbea-ring on safety in operations, must be established by tests.
FAR 23.603 : Materials and workmanship.
(a)
[The suitabilityanddurability of materialsusedforparts,thefailure of which could adversely a.ect safety, must–
(1)
Be establishedby experience ortests;]
(2)
Meet approved speci.cations that ensure their having the strength and other properties assumedinthedesigndata;[and
(3)
Takeinto account the e.ects of environmental conditions, such as temperature and humidity, expected in service.]
(b)
Workmanship must be of a high standard. Amdt. 23-23, E.. 12/01/78
FAR 23.605 : Fabrication methods.
(a)
[The methods of fabrication used must produce consistently sound structures. If a fabricationprocess(such asgluing, spot welding, orheat-treating) requiresclose control to reach this objective, the process must be performed under an approved process speci.cation.
(b)
Each new aircraft fabrication method must be substantiated by a test program.] Amdt. 23-23, E.. 12/01/78
FAR23.607 :[Fasteners.]
(a)
[Eachremovable fastener must incorporate two retaining devices if the loss of such fastener would preclude continued safe .ight and landing.
(b)
Fasteners and their locking devices must not be adversely a.ected by the environ-mental conditions associated with the particular installation.
(c)
No self-locking nut may be used on any bolt subject to rotation in operation unless a non-friction locking device is used in addition to the self-locking device.]
Amdt. 23-48, E.. 03/11/96
FAR 23.609 : Protection of structure.
Eachpart of the structure must–
(a)
Be suitably protected against deterioration or loss of strength in service due to any cause, including–
(1)
Weathering;
(2)
Corrosion; and
(3)
Abrasion; and
(b)
Have adequate provisions for ventilation and drainage.
FAR23.611 :Accessibility[provisions.]
[For each part that requires maintenance, inspection, or other servicing, appropriate meansmustbeincorporatedintothe aircraftdesigntoallowsuch servicing tobeaccom-plished.] Amdt. 23-48, E.. 03/11/96
FAR 23.613 : Material strength properties and design values.
(a)
Material strength properties must be based on enough tests of material meeting speci.cations to establish design values on a statistical basis.
(b)
[Design values mustbe chosento minimize theprobabilityof structuralfailuredue to material variability.Except asprovidedinparagraph(e) of this section, compliance with thisparagraph mustbe shownby selecting design valuesthat ensurematerial strength with the following probability :
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：FAA规章 美国联邦航空规章 Federal Aviation Regulations 2(22)
