(b) If the fault continues:
- remove the same RMP
- do a check and repair if necessary the wiring of the VOICE/DATA SELECT OUTPUT from the pin A/G of the RMP to the RMP derivation terminal block (Ref. ASM 46-21/05)
(c) If the fault continues:
- do a check and repair if necessary the wiring of the VOICE/DATA MONITOR INPUT from the RMP derivation terminal block to pin A/F of the RMP (Ref. ASM 46-21/05)
- install the RMP that you removed.
(2) If you cannot set the DATA mode on the two other RMPs:
(a) Remove the ATSU (1TX1) (Ref. AMM TASK 46-21-34-000-001)
- do a check and repair if necessary the wiring of the REMOTE VOICE/DATA SELECT from pin AA/15A of the ATSU to the RMP derivation terminal block (Ref. ASM 46-21/05)
(b) If the fault continues:
- do a check and repair if necessary the wiring of the PORT SELECT DISCRETE from AA/12B of the ATSU to the RMP derivation terminal block (Ref. ASM 46-21/05).
(c) If the fault stops:
- install the ATSU (Ref. AMM TASK 46-21-34-400-001)
(d) If the fault continues:
- install a new ATSU (Ref. AMM TASK 46-21-34-400-001).
B. Do the test given in Para. 3.A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 151-199, 201-299, 301-399, ∞∞46-21-00∞∞∞∞∞∞∞∞∞∞Page 238
401-499, Aug 01/05 CES
No VOICE mode set through the RMPs
1. Possible Causes
_______________
- RMP-COM/NAV FREQ SEL, 1 (1RG1)
- RMP-COM/NAV FREQ SEL, 2 (1RG2)
- RMP-COM FREQ SEL, 3 (1RG3)
- ATSU (1TX1)
- wiring of the VOICE/DATA SELECT OUTPUT
- wiring of the VOICE/DATA MONITOR INPUT
- wiring of the REMOTE VOICE/DATA SELECT
- wiring of the PORT SELECT DISCRETE
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 23-13-13-000-001 Removal of the Radio Management Panel (CRMP) (1RG1, 1RG2, 1RG3) AMM 23-13-13-400-001 Installation of the Radio Management Panel (CRMP)
(1RG1, 1RG2, 1RG3) AMM 46-21-00-710-001 Operational Test of the ATSU AMM 46-21-34-000-001 Removal of the Air Traffic Service Unit (ATSU) (1TX1) AMM 46-21-34-400-001 Installation of the Air Traffic Service Unit (ATSU)
(1TX1)
ASM 46-21/05
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the ATSU (Ref. AMM TASK 46-21-00-710-001) from the step 35. Do it again for each RMP.
4. Fault Isolation
_______________
A. If you cannot select the VOICE mode from one RMP, do the fault isolation procedure that follows:
(1) If you can correctly set the VOICE mode on the two other RMPs
(a) Replace the RMP-COM/NAV FREQ SEL, 1 (1RG1), RMP-COM/NAV FREQ SEL, 2 (1RG2) or RMP-COM FREQ SEL, 3 (1RG3) on which it was not possible to set the VOICE mode (Ref. AMM TASK 23-13-13-000-001) and (Ref. AMM TASK 23-13-13-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 151-199, 201-299, 301-399, ∞∞46-21-00∞∞∞∞∞∞∞∞∞∞Page 239
401-499, Aug 01/05 CES
(b) If the fault continues:
- remove the same RMP
- do a check and repair if necessary the wiring of the VOICE/DATA SELECT OUTPUT from the pin A/G of the RMP to the RMP derivation terminal block (Ref. ASM 46-21/05)
(c) If the fault continues:
- do a check and repair if necessary the wiring of the VOICE/DATA MONITOR INPUT from the RMP derivation terminal block to pin A/F of the RMP (Ref. ASM 46-21/05)
- install the RMP that you removed.
(2) If you cannot set the VOICE mode on the two other RMPs:
(a) Remove the ATSU (1TX1) (Ref. AMM TASK 46-21-34-000-001)
- do a check and repair if necessary the wiring of the REMOTE VOICE/DATA SELECT from pin AA/15A of the ATSU to the RMP derivation terminal block (Ref. ASM 46-21/05)
(b) If the fault continues:
- do a check and repair if necessary the wiring of the PORT SELECT DISCRETE from AA/12B of the ATSU to the RMP derivation terminal block (Ref. ASM 46-21/05).
(c) If the fault stops:
- install the ATSU (Ref. AMM TASK 46-21-34-400-001) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 Trouble Shooting Manual 排故手册 信息系统(21)
