4. Procedure
_________ (Ref. Fig. 401/TASK 75-41-15-991-300) Subtask 75-41-15-020-050
A. Remove the Nacelle Temperature Sensor
(1) Disconnect the connector (4) from the sensor (6).
(2) Install blanking caps on the connector and on the nacelle temperature sensor (4).
(3) Loosen the flanged nuts (1), the bolts (3) and disengage the clamp (5).
F 『 EEFF : ALL E Page 40275-41-15
E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E
Nacelle Temperature Sensor
Figure 401/TASK 75-41-15-991-300
F 『 EEFF : ALL E Page 40375-41-15
E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E E E
(4) Remove the nacelle temperature sensor (6) from its support (2).
F 『 EEFF : ALL E Page 40475-41-15
E E Feb 01/98 E E ECES E TASK 75-41-15-400-041
F 『
E C F M E
E E
E 56-5B E
E E
Installation of the Nacelle Temperature Sensor
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 1 m (3 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 73-25-34-710-043 Operational Test of the Engine Interface Unit 78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors 75-41-15-991-300 Fig. 401
3. Job Set-up
__________
Subtask 75-41-15-860-055
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
F 『 EEFF : ALL E Page 40575-41-15
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the access platform is in position. Subtask 75-41-15-010-060
B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. TASK 71-13-00-010-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2) Make sure that the thrust reverser doors are open (Ref. TASK 78-36-00-010-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 75-41-15-040-056
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
4. Procedure
_________
(Ref. Fig. 401/TASK 75-41-15-991-300) Subtask 75-41-15-420-050
A. Install the Nacelle Temperature Sensor
(1) Install the nacelle temperature sensor (6) on its support (2).
(2) Install the clamp (5), the bolts (3) and the flanged nuts (1) and then tighten them.
(3) Remove the blanking caps.
(4) Connect the connector (4) to the nacelle temperature sensor (6).
F 『 EEFF : ALL E Page 40675-41-15
E E Feb 01/98 E E ECES E Subtask 75-41-15-710-050
F 『
E C F M E
E E
E 56-5B E
E E
B. Do an operational test of the EIU (Ref. TASK 73-25-34-710-043) and make sure that on the CFDS no message related to the nacelle temperature sensor comes into view.
5. Close-up
________ Subtask 75-41-15-410-050
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the thrust reverser doors (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 75-41-15-440-052
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AIR 空气(72)
