曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
and if TOGA thrust is not required, proceed as follows:
SET the THRUST levers to TOGA detent, then retard the THRUST levers as required.
This enables to engage the GO-AROUND phase, with associated AP/FD modes.
SELECT the applicable AP/FD and A/THR modes on the FCU.
For RNP AR, the NAV mode must be re-engaged immediately.
Note: If the thrust levers are not set briefly to TOGA detent:
The FMS does not engage the GO AROUND phase, ‐ and flying over, or close to the
airport (less than 7 nm) will sequence the Destination waypoint in the F-PLN.
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
STANDARD OPERATING PROCEDURES - GO-AROUND
A318/A319/A320/A321 FLEET PRO-NOR-SOP-23 P 5/6
FCOM 19 AUG 10
GO AROUND WITH NO FD
Applicable to:
A go-around may have to be maid without FD guidance (visual or non-precision approaches).
Apply the following three actions simultaneously:
THRUST levers...........................................................................................................................TOGA
ROTATION.....................................................................................................................15 ° OF PITCH
Rotate to 12.5 °, if one engine is out.
GO AROUND..................................................................................................................... ANNOUNCE
FLAPS lever....................................................................................................... RETRACT ONE STEP
POSITIVE CLIMB...............................................................................................................ANNOUNCE
LDG GEAR......................................................................................................................... SELECT UP
AT GO-AROUND THRUST REDUCTION ALTITUDE
Disregard CLB or LVR CLB flashing on the FMA.
For a go-around with no FD, thrust reduction and acceleration altitude should be the same.
Select speed target to green dot.
Adjust aircraft attitude to 10/12 °.
Select thrust levers to CL detent and activate the A/THR (if the autothrust is not automatically
engaged).
Set FD to ON. (Basic mode HDG V/S or TRK FPA engages).
Select appropriate mode.
Check FMA.
Retract the flaps at appropriate speeds.
Monitor go-around routing and first cleared altitude.
Note: If thrust levers are set to CL detent at thrust reduction altitude may occur, if the current
speed is above the speed target (Refer to PRO-NOR-SRP-01-80 MONITORING THE
GO-AROUND).
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
STANDARD OPERATING PROCEDURES - GO-AROUND
Intentionally left blank
A318/A319/A320/A321 FLEET PRO-NOR-SOP-23 P 6/6
FCOM 19 AUG 10
A318/A319/A320/A321 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
NORMAL PROCEDURES
STANDARD OPERATING PROCEDURES - AFTER LANDING
A318/A319/A320/A321 FLEET PRO-NOR-SOP-24 P 1/4
FCOM 19 AUG 10
AFTER LANDING
Applicable to: ALL
LAND lights.......................................................................................................................... RETRACT
Retract landing lights, unless they are needed.
STROBE selector........................................................................................................................AUTO
When leaving the runway, set the STROBE lights to AUTO.
OTHER EXT LIGHTS............................................................................................................ AS RQRD
External lights can be turned off, unless they are needed.
Set the NAV & LOGO to ON, as required, to turn on the navigation and logo lights .
Applicable to: ALL
GROUND SPOILERS............................................................................................................... DISARM
Applicable to: ALL
RADAR................................................................................................................................ OFF/STBY
Applicable to: ALL
PREDICTIVE WINDSHEAR SYSTEM .....................................................................................OFF
Switching the radar and predictive windshear system OFF after landing avoids risk of radiating
persons at the gate area.
Applicable to: ALL
ENG MODE selector....................................................................................................................NORM
Applicable to: ALL
FLAPS.................................................................................................................................. RETRACT
Set the FLAPS lever to position 0.
If the approach was made in icing conditions, or if the runway was contaminated with slush or snow,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
A320机组操作手册FLIGHT CREW OPERATING MANUAL 12(41)
