GENERAL INFORMATION TASK INTRODUCTION
- RANGE - ELECTRICAL POWER APPLICATION
- DIMENSIONS - HYDRAULIC POWER APPLICATION
- ENGINES - EQUIPMENT COOLING
- FLIGHT CONTROLS - COMMUNICATION
- DOORS - TOWING
- FLIGHT COMPARTMENT PANELS - CDU OPERATION
- ELECTRONIC EQUIPMENT RACKS
- ELECTRICAL
737 GENERAL - INTRODUCTION
00-00-00
737-600/700/800/900 TRAINING MANUAL 737 GENERAL -- RANGE Introduction
The 737-800 is a two-engine airplane. It is for short to medium range flights with a capacity of up to 189 passengers.
Features
There are many new features. These new features increase the airplane payload, service ceiling, and range.
The airplane has a design range of 2,900 nautical miles.
00-00-00
00-00-00-002 Rev 1 08/22/2000
737-600/700/800/900 TRAINING MANUAL
737-800 RANGE
(2,900 NM)
OSLO
LONDON
PARIS
KARACHI BEIJING
MUMBAI
SEATTLE
NEW YORK SINGAPORE
MEXICO CITY
PORT MORESBY
BOGOTA
PERTH
737 GENERAL - RANGE
00-00-00
737-600/700/800/900 TRAINING MANUAL 737 GENERAL -- STRUCTURE DIMENSIONS General
These are the general dimensions of the airplane.
00-00-00
737-600/700/800/900 TRAINING MANUAL
00-00-00-511 Rev 1 04/23/2001
117 FEET 5 INCHES
34.3 METERS
47 FEET 1 INCH
14.4 METERS
129 FEET 6 INCHES
39.5 METERS
41 FEET 2 INCHES
12.6 METERS
737-800 DIMENSIONS
737 GENERAL - STRUCTURE DIMENSIONS
00-00-00
737-600/700/800/900 TRAINING MANUAL 737 GENERAL -- FUSELAGE DIMENSIONS General
Dimensions give locations on the fuselage. The scale for each dimension is inches. You use these dimensions to find components on the fuselage:
-Body station line
-Body buttock line
-Water line.
The body station line (STA) is a horizontal dimension. It starts at station line zero. You measure the body station line from a vertical reference plane that is forward of the airplane.
The body buttock line (BL) is a lateral dimension. You measure the buttock line to the left or right of the airplane center line.
The water line (WL) is a height dimension. You measure the water line from a horizontal reference plane below the airplane.
00-00-00
00-00-00-530 Rev 1 04/18/2001
STATION LINES STA 500 WL 306.5
LBL 73.75
LBL 30
RBL 30 RBL 73.75 WL 232.5
WL AT TOP OF WL 208
FLOORBOARD FWD
WL 148.5 BBL 0 BODY BUTTOCK AND WATER LINES 737 GENERAL - FUSELAGE DIMENSIONS
- 11 -
00-00-00
737-600/700/800/900 TRAINING MANUAL 737 GENERAL -- WING REFERENCE DIMENSIONS Wing Reference Dimensions
The wing has two reference dimensions. These reference dimensions give wing locations in inches. Measure each location from buttock line 0. These are the wing reference dimensions:
-Wing station
-Wing buttock line.
You measure the wing station perpendicular to the wing leading edge.
You measure the wing buttock line parallel to the buttock line.
For more information, see the maintenance manual and the maintenance planning data document.
00-00-00
737-600/700/800/900 TRAINING MANUAL
WING
WBL 709.40
737 GENERAL - WING REFERENCE DIMENSIONS
00-00-00
737-600/700/800/900 TRAINING MANUAL 737 GENERAL -- VERTICAL STABILIZER REFERENCE DIMENSIONS Vertical Stabilizer Reference Dimensions
The vertical stabilizer has four reference dimensions. These reference dimensions give vertical stabilizer locations in inches. These are the vertical stabilizer reference dimensions:
-Vertical stabilizer station
-Vertical stabilizer leading edge station
-Rudder station
-Vertical stabilizer waterline.
Measure the vertical stabilizer station perpendicular to the vertical stabilizer rear spar. Vertical stabilizer station 0 starts at the body crown line.
Measure the vertical stabilizer leading edge station perpendicular to the vertical stabilizer leading edge. Vertical stabilizer leading edge station 0 starts at the body crown line.
Measure the rudder station perpendicular to the rudder hinge centerline. Rudder station 0 starts at the body crown line.
Measure the vertical stabilizer waterline parallel to the body waterline.
For more information, refer to the maintenance manual and the maintenance planning data document.
00-00-00-532 Rev 1 12/01/1998
- 14 -
00-00-00
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-600/700/800/900培训手册 TRAINING MANUAL 1(6)
