20-10-11
ALL ú ú 01 Page 402 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
HOSE OR CONDUIT
WOVEN NYLON SLEEVING
STEP 1
TEN WRAPS APPROXIMATELY
STEP 2
0.75 1.50
CUT OFF 0.25 MAX STEP 3 (LACING) OF THE SERVING FROM EITHER END TIE CAN BE MADE CUT OFF 0.25 MAX
FOR TWO OR MORE HOSES
NOTE: ALL DIMENSIONS ARE IN INCHES.
Protective Lacing Installation Figure 401
K26097
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-11
ALL ú ú 01 Page 403 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
S 404-015
(2) Install the protective lacing on the nose landing gear per Figure 401, steps 1 through 3.
(a)
Prior to pulling the lock lace through, (before step 3), apply adhesive to laces.
(b)
Pull the laces into place, (step 3), this will bond the laces in place.
(c)
Apply two layers of tape over the lacing. 1) Spirally wrap each layer with a 50% overlap and reverse the direction of the spiral with each layer.
2) Extend the tape 1.0 inch to 1.5 inch beyond each end of the lacing.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-11
ALL ú ú 01 Page 404 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
PRESSURE-SENSITIVE DECALS - REMOVAL/INSTALLATION
________________________________________________
1. General_______
A. This procedure has these two tasks:
(1)
Pressure-Sensitive Decal Removal.
(2)
Pressure-Sensitive Decal Installation.
B. Apply the external decal sections in a sequence that puts the end with the overlap downstream from the line of flight.
C. All exterior decals require edge sealing using paint or an edge sealer unless specified differently.
D. Clean the plastic film decals with naphtha.
E. Remove air bubbles during the 8 hours after you apply the decal. Make a hole in the decal film with a sharp pointed instrument, at the edge of bubble, and push air out through the hole.
F. You can also install interior decals with the same procedure that you use to install pressure-sensitive placards (AMM 20-10-13/401).
TASK 20-10-12-004-001
2. Pressure-Sensitive Decal Removal________________________________
A. Equipment
(1)
Plastic scraper or spatula
(2)
Source of heat - 120°F: for example, hot air
blast or light bulb
B. Consumable Materials
(1)
B00130 Ethyl Alcohol, Denatured
(2)
B00148 Methyl Ethyl Ketone (MEK)
(3)
B00666 Methyl Propyl Ketone (MPK)
(4)
G00033 Cheesecloth - BMS 15-5
C. References
(1)
AMM 20-30-89/201, Solvent - Series 89
(2)
AMM 51-21-01/701, Paint Stripping
D. Remove External Decals
S 024-002
(1) Use the Paint Stripping procedure to remove external decals (AMM 51-21-01/701).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-12
ALL ú ú 01 Page 401 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
E. Remove Internal Decals
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 STANDARD PRACTICES - AIRFRAME(55)
