(2)
C00259 Primer - BMS 10-11, Type 1
(3)
B00010 Solvent - General Cleaning of Metal (Series 80)
(4)
B00138 Abrasive cloth - 240-grit, P-C-451
D. Prepare Tube for Installation
S 948-303
WARNING: DO NOT USE PERMASWAGE FITTINGS ON ANY OXYGEN LINES OR ON FLUID
_______ LINES INSIDE THE FIRE ZONES OF ENGINES OR APU'S. DAMAGE TO EQUIPEMENT OR INJURY TO PERSONS CAN OCCUR.
(1)
Use the tools shown in Fig. 825.
S 948-304
(2)
Cut out the damaged section of the tube:
(a)
Make sure the section you cut out of the tube is a straight section with a minimum straight length as shown in Fig. 826. This will make sure the fitting and swage tool will fit.
(b)
Use one Permaswage fitting for the repair if the damaged section is no more than 0.150 inch long. In this case, the cut can be through the center of the damaged section.
(c)
If the damage is too near to a bend (less than 1/2 "A", Fig. 826) or longer than 0.150 inch, use a tube splice and two fittings to make the repair.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-09
ALL ú ú 01 Page 825 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 757 MAINTENANCE MANUAL
(3) S 948-305For tube cutouts with a bend, use the cutout tube section as a template to mark and cut the new tube segment.
NOTE:____ The maximum gap between the tube ends is approximately 0.150 inch for the union installation.
(4) S 118-306Clean the tube in the swage area: (a) Clean the not painted tube sections that you will repair with solvent, Series 80 (AMM 20-30-80/201). (b) Make sure the sections are free of dirt, grease, and other unwanted material for a distance equal to the values shown in Fig. 826. (c) Remove paint and anodize from the tubes in an area equal to the values shown in Fig. 826. Use the methods shown in Fig. 828. (d) Make sure the cleaned surfaces are smooth, uniform, bright, and free of unwanted materials. (e) Use a brush to apply a layer of Alodine 1200 to the open surfaces of aluminum tubes.
(5) S 948-307Remove burrs from the tube ends: (a) To remove burrs from the inner bore of the tube ends, use Deutsch plug-type deburring tools or equivalent. Refer to Fig. 804 for the correct deburring procedure.
NOTE:____ You must remove burrs from the tube inner diameter each time you cut the tube. Make sure the tube shavings do not get into the system.
Do not release the spring pressure of the deburring tool while you pull the tool from the tube.
(b) It is not usually necessary to remove burrs from the tube outer diameter. If it is necessary, use 240-grit abrasive cloth. Use a clean cloth to remove particles.
(6) S 948-308Use one of these steps to apply witness marks: (a) Use a felt pen or equivalent to apply witness marks as shown in Fig. 829. Use Deutsch tools D12580-1, -2, -3 only or equivalent. (b) Make marks directly on the tube to show the minimum insertion depths as shown in Fig. 829. Swage fittings to the marks.
(7) S 378-309Apply paint to bare areas. For example, tool marks and areas where you removed paint (fittings and painted tubes).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-09
ALL ú ú 01 Page 826 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
S 378-310
(8) Apply alodine 1200 to open areas of aluminum and BMS 10-11 primer to all other tubes and fittings.
E. Procedure
(1) S 868-311Remove pressure from the systems where you will do the repair.
(2) S 948-312Use a union and a tube as shown in Fig. 824.
NOTE:____ Keep the Permaswage fittings in their container until you are ready to install them.
(3) S 358-313Make sure the tube is sufficiently long to do the repair (Fig. 826).
(4) S 118-314Clean the tube as shown in Fig. 828, then cut the tube.
NOTE:____ Seal the tube ends with a cap if you do not join the tubing immediately.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 STANDARD PRACTICES - AIRFRAME(33)
