*
Backrest cushion
*
Seat pan
*
Seat cushion
*
Seat belt and shoulder harness (not shown)
*
Seat structure
*
Stowage compartment doors.
The wall mounted attendant seats have these parts:
*
Headrest cushion
*
Backrest cushion
*
Seat cushion
*
Seat belt and shoulder harness (not shown)
*
Seat structure.
The cushions attach to the seat structure with hook and loop tape. Remove the covers from the cushions to dry clean the covers.
Clips (not shown) attach the seat belts and shoulder harness to the seat structure. You can remove the seat belts and shoulder harness to clean them.
Functional Description
The seat structure has a seat pan which folds down. A spring folds the seat pan up when there is no weight on it. A damper (not shown) causes the seat pan to fold up slowly.
The seat track mounted attendant seats have springs (not shown) which cause the stowage compartment doors to close. Latches hold the doors closed. The latch striker plates are adjustable.
The stowage compartment below the seat of the wall mounted attendant seat has a door which folds down. To unlatch the door, move the door latch left or right.
Training Information Point
In seats with handsets or switch panels, electrical connectors (not shown) connect the seat wiring to the airplane wiring.
EFFECTIVITY BEJ ALL 25-25-02
Page 1
D633W101-BEJ Sep 05/2003
PASSENGER COMPARTMENT SEATS -ATTENDANT SEATS
Four seat track fittings attach the seat track mounted attendant seat to the seat tracks.
The wall mounted attendant seats attach with bolts to vertical structure. To remove the seat, you must get access to the bolts as follows:
*
Move the head rest up
*
Remove the back rest
*
Open the lower stowage compartment door.
EFFECTIVITY BEJ ALL 25-25-02
Page 2
D633W101-BEJ Sep 05/2003
PASSENGER COMPARTMENT SEATS -ATTENDANT SEATS
EFFECTIVITY BEJ ALL 25-25-02
Page 3
D633W101-BEJ Sep 05/2003
BUFFET AND GALLEY -INTRODUCTION
Purpose
The cabin crew uses galleys to store and prepare food and beverages.
General Description
These are typical galley inserts:
*
Oven
*
Refrigerator
*
Coffee maker
*
Sink
*
Storage
*
Waste container
*
Serving carts.
Galleys can have a different number and types of service connections. These are the typical connections:
*
Electrical power
*
Water
*
Refrigeration air
*
Conditioned air
*
Ventilation.
The usual location for most galley service connections are above the galley. If galleys A1, A2 or A3 require a water service connection, the connection is near the floor, aft of the galley. If any galley requires a waste water drain connection, the connection is always near the galley floor.
EFFECTIVITY
BEJ ALL
Some galleys have air chillers, external to the galleys to supply cold air for refrigeration. All galleys forward of the aft cabin doors, can have air chillers that mount above the galley in the ceiling area. Galleys aft of the aft cabin doors, can have air chillers in the lower lobe area, aft of the bulk cargo compartment.
The airplane has flex and fixed galleys. Flex galleys attach to the seat tracks. You can install or move the galley anywhere in the flexibility zones. Fixed galleys go in a specific place in the airplane and you cannot move them.
There are two kinds of flex galleys, center and outboard. Center flex galleys have straight sides and go in the center of the passenger compartment. Outboard flex galleys have a curved side to fit against the side of the passenger compartment.
See the Interior Reconfiguration Document for information to change the location of the galleys in a flex zone.
Location -Flex Galleys
These are the possible center flex galley positions:
*
F-5 (forward)
*
M-1 (door 2)
*
M-2 (door 2)
*
A-4 (aft).
These are the possible outboard flex galley positions at door 2:
25-30-00
Page 1 D633W101-BEJ Sep 05/2002
BUFFET AND GALLEY -INTRODUCTION
*
MS-1
*
MS-2
*
MS-3
*
MS-4.
Location -Fixed Galleys
These are the possible forward fixed galley positions:
*
F-1 (forward)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：777 AMM 飞机维护手册 Equipment and Furnishings(11)
