S 842-030
(18)
For the alternate static ports and the elevator feel static ports use the following static port cover procedure (see Fig. 202 Sheets 1 and 2 for illustrations of the static port cover placement procedure).
WARNING: DO NOT PLACE 3M NO. 471 YELLOW VINYL ADHESIVE TAPE OVER
_______ THE HOLES OF THE STATIC PORTS.
(a) Clean the area around each static port with aliphatic naphtha or equivalent, and a clean dry rag where you will put the 3M No. 471 yellow vinyl adhesive tape (see Fig. 202 Sheet 1).
ú (b) Place one end of approximately a 4-foot piece of the orange
ú barricade tape over the holes of the static port and secure the upper edge with 5 inches of 3M No. 471 yellow vinyl adhesive tape (see Fig. 202 Sheet 1, Steps 1 and 2).
NOTE: Smooth the 3M No. 471 yellow vinyl adhesive tape on the
____ airplane surface to make sure the bond is satisfactory.
1) Do not put vinyl adhesive tape over the holes of the static ports.
(c)
Put a 5-inch piece of 3M No. 471 vinyl adhesive tape on each vertical edge of the barricade tape overlapping the first strip of adhesive tape (see Fig. 202 Sheet 1, Step 3).
(d)
Put an 8-inch piece of 3M No. 471 vinyl adhesive tape horizontally over the barricade tape below the static port holes, overlapping the two vertical strips of adhesive tape (see Fig. 202 Sheet 1, Step 4)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
10-11-01
ALL ú ú 03.1 Page 206 ú Sep 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
(e)
Carefully grasp the free section of the barricade tape and fold it back up against the surface of the airplane. Place an 8-inch strip of the No. 471 vinyl adhesive tape horizontally over the back side of the barricade tape overlapping the lower half of the first 8-inch strip of No. 471 vinyl adhesive tape (see Fig. 202 Sheet 2, Steps 5 and 6).
(f)
Allowing the barricade tape to stream down, place an 8-inch strip of 3M No. 471 yellow vinyl adhesive tape horizontally over the barricade tape half way down the length of the barricade tape (see Fig. 202 Sheet 2, Step 7).
(g)
Place an 8-inch strip of 3M No. 471 yellow vinyl adhesive tape horizontally over the lower end of the barricade tape (see Fig. 202 Sheet 2, Step 8).
S 842-032
(19) For the primary static ports use the following static port cover procedure (see Fig. 203 Sheets 1 and 2 for illustrations of the static port cover placement procedure for the primary static ports).
WARNING: DO NOT PLACE 3M NO. 471 YELLOW VINYL ADHESIVE TAPE OVER
_______
THE HOLES OF THE STATIC PORTS.
(a)
Clean the area around each primary static port with aliphatic naphtha or equivalent, and a clean dry rag where you will put the 3M No. 471 yellow vinyl adhesive tape (see Fig. 203 Sheet 1).
(b)
Place one end of a 3-foot piece of the orange barricade tape over the holes of the upper primary static port and secure the upper edge with 5 inches of 3M No. 471 yellow vinyl adhesive tape (see Fig. 203 Sheet 1, Steps 1 and 2).
NOTE: Smooth the 3M No. 471 yellow vinyl adhesive tape on the
____ airplane surface to make sure the bond is satisfactory.
1) Do not put vinyl adhesive tape over the holes of the static ports.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
10-11-01
ALL ú ú 01 Page 207 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
ALTERNATE STATIC PORTS PRIMARY STATIC PORTS
B
C
Pitot-Static System - Component Location Figure 201
H23751
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 PARKING, MOORING, STORAGE & RETURN TO S(4)
