F87615
System B Hydraulic Pump Case Drain Filter Installation 500
29-12-71 Figure 401 Aug 15/67
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
D. Position filter assembly on mounting bracket and install filter mounting bolts.
E. Remove caps from hydraulic lines and connect hydraulic lines to case drain filter and check valve.
F. Reconnect pump supply hose to system B reservoir quick disconnect fitting.
CAUTION: WHEN INSTALLING PUMP SUPPLY LINE QUICK DISCONNECT FITTING, ENSURE THAT INDICATOR PINS ARE EXTENDED. IF PINS ARE NOT EXTENDED, FLUID SUPPLY TO PUMP WILL BE RESTRICTED OR COMPLETELY STOPPED, AND PUMP DAMAGE OR OVERHEATING MAY RESULT.
G. Pressurize hydraulic reservoirs (Ref 29-09-300 MP).
H. Close SYSTEM B NORMAL and ALTERNATE circuit breakers and pressurize hydraulic system B using applicable pump (Ref 29-12-0 MP).
I. Check filter for leaks.
500
May 01/75 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 29-12-71 Page 403
SYSTEM B HYDRAULIC RETURN FILTER - UNIT SERVICING
1. General
A. A container will be necessary to catch fluid when removing the filter bowl. Should any fluid spill on the airplane, decontaminate. Refer to Chapter 12, Cleaning and Washing.
2. Equipment and Materials
A. Skydrol Assembly Lube - MCS 352 or Fire Resistant Hydraulic Fluid – BMS 3-11
3. Prepare Return Filter for Servicing
A. Depressurize hydraulic system B. Refer to 29-12-0, Hydraulic System B-MP.
B. Depressurize system B reservoir. Refer to 29-09-300, Hydraulic Reservoir Pressurization System - MP.
C. Open system B pump circuit breakers on P6-11 and P6-12 panels.
4. Replace Return Filter Element
A. Remove Return Filter Element
(1)
Remove filter bowl (4, Fig. 301).
NOTE: When filter bowl is removed, shutoff valve (2) closes and prevents fluid from draining from the system.
(2)
Remove filter element (5) from filter bowl.
(3)
Clean filter bowl (4) and filter head (1) thoroughly and dispose of element.
500
Feb 15/73 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 29-12-81 Page 301
B. Install Return Filter Element
(1)
Lubricate O-rings and filter bowl threads with assembly lube or hydraulic fluid.
(2)
Install O-ring (7, Fig. 301) on filter element (5) and place element in filter bowl.
(3)
Deleted.
(4)
Screw filter bowl (4) into filter head (l), hand tighten filter bowl until it reaches stop (3). Do not use wrench.
CAUTION: DURING INSTALLATION, IT IS IMPERATIVE THAT EXTREME CARE BE TAKEN TO PREVENT IMPURITIES FROM ENTERING THE SYSTEM.
(5)
Pressurize system B reservoir (Ref 29-09-300).
(6)
Pressurize system B hydraulic system and check filter bowl for leaks (Ref 29-12-0).
(7)
Lockwire filter bowl.
NOTE: If leakage occurs at the filter bowl, replace the hydraulic return filter assembly (Ref 29-12-81/401). The leaking O-ring (6) is covered by a sleeve when the filter bowl is removed. Special tools are required to disassemble the filter to permit replacement of the O-ring.
500
29-12-81 Page 302 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Aug 01/94
F87622
500 System B Hydraulic Return Filter Servicing
Aug 15/73 Figure 301 29-12-81
Page 303
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:737 AMM 飞机维护手册 液压 HYDRAULIC POWER(63)