A. Install the Throttle Control Artificial Feel Unit as follows:
(1) Install the throttle control artificial feel unit (23).
(2) Install the 2 bolts (24), 2 washers (22) and 2 nuts (21).
(3) If necessary bond the bushes (25) on the bolts (26) with loctite 675 (Material No. CP2188).
(4) Install the 2 bolt assemblies (26), the 2 washers (20) and the 2 nuts (19).
(5) Tighten the 4 nuts.
(6) Install 4 new cotter pins (18).
(7) Install the 4 rods (27).
(8) If necessary bond the 4 bushes (16) on the 4 bolts (17) with loctite 675 (Material No. CP2188).
(9) Install the 4 bolt assemblies (17), the 4 washers (15) and the 4 nuts (14).
(10) Tighten the 4 nuts.
Subtask 76-11-17-820-052
B. Adjustment of the mechanical linkage:
(1) Make sure that you can easily install and remove the rigging pin
R RIGGING PIN (98DNSA20208080) (12) in the artificial feel unit (23). (Ref. Fig. 403/TASK 76-11-17-991-910)
(a) If you can not do this, adjust the length of the rod (Ref. TASK 76-11-00-820-044).
F 『 EEFF : ALL E Page 41176-11-17
E E May 01/99 E E ECES E
Throttle Control Artificial Feel Unit
Figure 404/TASK 76-11-17-991-911
F 『 EEFF : ALL E Page 41276-11-17
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(2) Make sure that you can easily install and remove the rigging pin RIGGING PIN (98DNSA20206080) (11) in the throttle control unit. (Ref. Fig. 403/TASK 76-11-17-991-910)
(a) If you cannot do this, adjust the length of the rod (Ref. TASK 76-11-00-820-044).
Subtask 76-11-17-420-054
C. Install 4 news cotter pins (13).
Subtask 76-11-17-080-052
D. Remove the rigging pin (12) from the artificial feel unit and the rigging pin (11) from the throttle control unit.
Subtask 76-11-17-480-053
E. Install the THROTTLE LEVER LOAD MEASURE (98D76103000000) on the throttle control levers.
Subtask 76-11-17-820-053
F. Adjustment of the Artificial Feel Unit:
(1) Measure the value necessary to move the throttle control lever between the IDLE STOP and the MAX CLIMB.
(a) This value must be 0.8 +0.1 -0 daN (1.8 +0.2 -0 lbf). NOTE : Measure this value in the IDLE STOP to MAX CLIMB range. Do
____ not measure this value at the hard point where the load increases suddenly.
(2) Measure the value necessary to move to more than MAX CLIMB hard point.
R (a) This value must be 2.5 +0.1 -0 daN (5.62 +0.22 -0 lbf).
(3) If you do not get these values, adjust the artificial feel unit (Ref. TASK 76-11-00-820-045)
Subtask 76-11-17-080-053
G. Remove the tool from the throttle control levers.
F 『 EEFF : ALL E Page 41376-11-17
E E Aug 01/04 E E ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 76-11-17-410-052
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Install the plates (4) and (10).
(Ref. Fig. 402/TASK 76-11-17-991-909)
(3) Install the washers (5) and the screws (6).
(4) Install the clamps (9).
(5) Install the ventilation plates (8).
(6) Install the screws (7).
(7) Install the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU. (Ref. Fig. 401/TASK 76-11-17-991-908)
NOTE : The installation procedure is the same for the FLOOD LT/INTEG
____
LT panel 111VU and FLOOD LT panel 112VU.
(a) Remove the blanking caps from the connectors (2) and (3).
(b) Install the connector (2) on the panel (1).
(c) Install the panel (1) on the structure.
(d) Fully tighten the fasteners on the panel (1).
(8) Install the Multipurpose Control and Display Units (3CA1 and 3CA2). (Ref. TASK 22-82-12-400-002).
(9) Install the Radio Management Panels (1RG1 and 1RG2) (Ref. TASK 23-13-13-400-001).
(10) Install the Audio Control Panels (2RN1 and 2RN2) (Ref. TASK 23-51-12-400-001).
(11) Install the Weather Radar Control Unit (3SQ) (Ref. TASK 34-41-12-400-001).
(12) Install the ATC Control Unit (3SH) (Ref. TASK 34-52-12-400-001)
F 『 EEFF : ALL E Page 41476-11-17
E E Feb 01/98 E E ECES E Subtask 76-11-17-410-053
F 『
E C F M E
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ENGINE CONTROLS 发动机控制(11)
