曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
I
IOTES:
I) CIU/DLS:
When the CIU or DLS is selected for test through the MFD’s, the system will reject the selection(s) ti a
CV SINS mode of alignment is in progress. This allows the SINS alignment to continue to completion
without interruption.
?) ASPJ:
In addltion to the interlock conditions indicated above, the following switch settings must be made on
the ASPJ control panel in order to initiate test:
-When the ASPJ is selected for test with the MFD’s, the ASPJ will perform BIT and radiate (i.e.,
transmit RF) only lf XMIT switch is selected. If RCV is selected, the ASPJ will perform BIT without
radiating.
-When the ASPJ Is seteoted for test with the MFDs, the ASPJ will not perform BIT if SlBy or OFF is
selected.
Figure 38-7. Interlock Test Restrictions (Sheet 1 of 2)
38.11 ORIGINAL
NAVAIR Ol-F~4AAD-~
3) INS:
Prior to selecting INS for test with the OBC NAV format, TEST on the NAV MODE panel must be
selected.
4) DPlIDP2:
When DPl or DP2 is selected for test through the OBC CD formats, the following restrictions apply:
ALLOWABLE TEST
SELECTION FLIGHT STATUS
DPI or DP2 In-flight (Weight off wheels), both DP’s must be operationally GO
OR
Preflight (Weight on wheels)
NONE In-flight (Weight off Wheels), one DP not operationally GO
5) MCl/MC2:
When MCI or MC2 is selected for test with the OBC AUXformats, the following restrictions apply:
ALLOWABLE TEST
SELECTION FLIGHT STATUS
MCI or MC2 In-flight (Weight off wheels), both MC’s must be operationally GO
OR
Preflight (Weight on wheels)
NONE In-flight (Weight off wheels), one MC not operationally GO
‘6) DSS:
Prior to selecting the DSS for test through the MFD’s, the data storage unit must be inserted into the
Data Storage Unit Receptacle (DSUR). DSS BIT will be limited (i.e., less bulk memory checksum test)
when the DSS is tested as part of a preflight or retest sequence. Otherwise, if the test selection is an
individual or functional group type made through the OBC AUX format, DSS BIT will include the
performance of the bulk memory checksum test. The bulk memory checksum test adds approximately
1 minute to the overall test time.
Figure 38-7. Interlock Test Restrictions (Sheet 2 of 2)
ORIGINAL 38.12
osc DISPLAY
FORMAT
ASIC
TEST SELECTIOM
TYPE
SEQUENCES:
Prelight
lnflight
Retest
unctional group Group or individual:
FLT (flight) AFCS, AICS, APC
CNI (communication, RFP, RFR, BAG, IFX,
navigation, IFI, RALT, TCN
identification)
NAV (navigation) CADC, CIU, DINS,
SAHR
CD (controls and
displays)
AUX (auxiliary)
DEU. DPl , DP2
MCI, MC2, EMSPl,
EMSP2, ADAC, DSS,
DBUS
SMST (stores
management system)
TAC (tactical)
EW (electronic
warfare)
SNSR (sensors)
SMS
DLC, JTIDS
ASPJ, BSF, IFB,
RWR, MFA
IRST, RDR, SDIS,
TARPS
:AIL DATA
CNI
NAV
CD
AUX
JTIDS
SMST
SMST SWITCHES
Ew
SNSR
MNTENANCE
;URRENT FAILURES
:AlLURE HISTORY FILE
NAVAIR 0%FIWD-I
TID OBCCM window will be affected. Format examples
are shown in Figure 38-11. Note that tbe OBC
maintenance formats are unaffected by any masking
operation. Masking and umna&ing is controlled via
OBC basic, any OBC functional group, or any fail data
format as follows:
1. OBC basic masking is performed by selecting tbe
MSK function on the OBC basic format, at which
time the MSK pushbutton legend will be boxed
This allows all the equipment failure acronyms
currently appearing on the OBC basic format to be
removed. Unmasking is performed by pressing the
MSK pushbutton while it is boxed, As a result,
failure acronyms are displayed for equipment currently
failed and the MSK pushbutton legend is
unboxed to indicate that no failures are masked.
The MSK pushbuttona ppearsb oxed on the OBC
BASIC format if there is at least one WRA failure
masked in the system.
2. Functional group masking is performed by selecting
the ALL and MSK pushbuttons on the respeotive
OBC functional group format. The ALL
pushbutton legend is boxed to indicate its selection
andu nboxed if deselectedG. roup masking is only
performed if the ALL pushbutton is boxed prior to
making the selection of the MSK pushbutton.
Group masking will only remove failure acronyms
associated with equipment on the corresponding
functional group format Group unmasking is performed
by deselecting the ALLJMSK pushbutton
when the MSK pushbutton legend is boxed. The
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
F-14D 飞行手册 Flight Manual 3(65)
