曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
battery is installed to provide up to three years battery back up.
SEL and CTL Buttons
All time keeping and set functions are addressable using the Select
and Control buttons below the time display. Upon power up the clock
will display Universal Time (UT). Pressing the Select button 3 times
will display Local Time (LT), and Elapsed Time (ET) sequentially.
Pressing the button again will return the display to UT.
Set UT or LT:
Use the Select button to select UT or LT as desired. Simultaneously
press Select and Control buttons (tens of hours LED will flash). Press
Control button repeatedly as required to increment digit to desired
value. Press Select button to select the next digit to be set. After all
digits have been set, press the Select button again to return to the
normal mode.
Flight Time (FT):
The flight time (FT) option is not available in this installation. If FT is
selected the display will ‘zero.’
Elapsed Time (ET):
The ET mode may be used either in ‘count-up’ or in ‘count-down’
modes.
To set the count-up mode:
1. Select ET using the Select button; and
March 2010
Information Manual 7-79
Cirrus Design Section 7
SR20 Airplane Description
2. Press Control to activate count-up timer. Elapsed time counts up
to 59 minutes, 59 seconds, and then switches to hours and
minutes. Pressing the Control button again will reset the timer to
zero.
To set the count-down mode:
1. Select ET using the Select button;
2. Input a ‘count-down’ time using the same technique as setting UT
or LT (a maximum of 59 minutes, 59 seconds may be entered);
3. Press the Select button to exit the set mode; and
4. Press Control to start the count down. At zero, the alarm activates
and the display flashes. Pressing either Select or Control
deactivates the alarm.
Test Mode:
To enter the self-test mode, hold the Select button for 3 seconds. The
display will indicate “88:88” and all four (UT, LT, FT, ET) annunciators
will come on.
OAT – VOLTS Button
The red OAT-VOLTS button is used to display Outside Air Temperature
and airplane main bus voltage. When the airplane is powered down,
the upper display will display the clock’s back-up battery voltage. Upon
power up, the display will show the airplane’s main bus voltage.
Pressing the button displays OAT in F. Pressing the button again
displays OAT in C.
March 2010
7-80 Information Manual
Section 7 Cirrus Design
Airplane Description SR20
Cirrus Airplane Parachute System
The SR20 is equipped with a Cirrus Airplane Parachute System
(CAPS) designed to bring the aircraft and its occupants to the ground
in the event of a life-threatening emergency. The system is intended to
saves the lives of the occupants but will most likely destroy the aircraft
and may, in adverse circumstances, cause serious injury or death to
the occupants. Because of this it is important to carefully read the
CAPS descriptions in this section, section 3 Emergency Procedures
and Section 10, Safety and consider when and how you would use the
system.
• WARNING •
The parachute system does not require electrical power for
activation and can be activated at any time. The solidpropellant
rocket flight path is upward from the parachute
cover. Stay clear of parachute canister area when aircraft is
occupied. Do not allow children in the aircraft unattended.
System Description
The CAPS consists of a parachute, a solid-propellant rocket to deploy
the parachute, a rocket activation handle, and a harness imbedded
within the fuselage structure.
A composite box containing the parachute and solid-propellant rocket
is mounted to the airplane structure immediately aft of the baggage
compartment bulkhead. The box is covered and protected from the
elements by a thin composite cover.
The parachute is enclosed within a deployment bag that stages the
deployment and inflation sequence. The deployment bag creates an
orderly deployment process by allowing the canopy to inflate only after
the rocket motor has pulled the parachute lines taut.
The parachute itself is a 2400-square-foot round canopy equipped with
a slider, an annular-shaped fabric panel with a diameter significantly
less than the open diameter of the canopy. The slider has grommets
spaced around its perimeter. The canopy suspension lines are routed
through these grommets so that the slider is free to move along the
suspension lines. Since the slider is positioned at the top of the
suspension lines near the canopy, at the beginning of the deployment
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
西锐20飞机信息手册 SR22 AIRPLANE INFORMATION MANUAL 1148-126(77)
