曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
Airborne Color Weather Radar WARNING: Begin transmitting only when it is safe to do so. If it is desired to transmit while the aircraft is on the ground, no personnel or objects should be within 11 feet of the antenna. CAUTION: In Standby Mode, the antenna is parked at the center line. It is always a good idea to put the radar in Standby Mode before taxiing the aircraft to prevent the antenna from bouncing on the bottom stop and possibly causing damage to the radar assembly.
D
isplaying Weather on the Weather Radar Page
1) Turn the large FMS Knob to select the Map Page Group.
2) Turn the small FMS Knob to select the Weather Radar Page.
3) Select the MODE Softkey.
4) If the aircraft is on the ground, select the STANDBY Softkey to initiate the one minute warm-up period. After the warm-up is complete, the radar will enter the Standby Mode. After the aircraft is airborne, select the WEATHER Softkey.
Or:
If the aircraft is already airborne, select the WEATHER or GROUND Softkey. The one-minute warm-up period will be initiated, after which the radar will begin transmitting. The horizontal scan is initially displayed.
5) Turn the Joystick to select the desired range.
6) If desired, select the VERTICAL Softkey for vertical scanning.
Adjusting Antenna Tilt
Move the Joystick up or down to adjust the tilt of the antenna up or down. Monitor
the displayed tilt value in the TILT field.
When scanning vertically, a Tilt Line may be displayed to aid in positioning the tilt of the antenna. If the Tilt Line is not displayed, perform the following steps:
1) Press the MENU Key
2) Turn the large FMS Knob to select ‘Show Tilt Line’.
3) Press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Cessna Citation Mustang 190-00600-02 Rev. A 40
Hazard Avoidance
Flight
EICAS Instruments
Nav/Com/
GPS Nav AFCS XPDR/Audio
Flight
Procedures Planning
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Index Appendix Alerts
Adjusting Antenna Bearing
Move the Joystick right or left to adjust the azimuth position of the antenna right or left. Monitor the displayed bearing value in the BEARING field.
When scanning horizontally, a Bearing Line may be displayed to aid in positioning the antenna for the vertical scan. If the Bearing Line is not displayed, perform the following steps:
1) Press the MENU Key
2) Turn the large FMS Knob to select ‘Show Bearing Line’.
3) Press the ENT Key.
Vertically Scan a Storm Cell
1) While in the Horizontal Scan view, move the Joystick to place the Bearing Line on the desired storm cell, or other area, to be vertically scanned.
2) Select the VERTICAL Softkey. A vertical ‘slice’ of the selected area will now be displayed.
3) Move the Joystick right or left to move the scanned “slice” a few degrees right or left.
4) Turn the Joystick to adjust the range.
5) To select a new area to be vertically scanned, select the HORIZON Softkey to return to the Horizontal Scan view and repeat the previous steps.
Adjusting Gain WARNING: Changing the gain in Weather Mode will cause precipitation intensity to be displayed as a color not representative of the true intensity. Remember to return the gain setting to ‘Calibrated’ for viewing the actual intensity of precipitation.
1) Select the GAIN Softkey to activate the cursor in the ‘GAIN’ field.
2) Turn the small FMS Knob to adjust the gain for the desirable level. The gain setting is visible in the gain field as a movable horizontal bar in a flashing box. The line pointer is a reference depicting the calibrated position.
3) Press the FMS Knob to remove the cursor.
4) Select the GAIN Softkey again to recalibrate the gain. ‘CALIBRATED’ will be displayed in the ‘GAIN’ field.
190-00600-02 Rev. A Garmin G1000 Cockpit Reference Guide for the Cessna Citation Mustang 41
Hazard Avoidance
Flight
Instruments EICAS
Nav/Com/
XPDR/Audio AFCS GPS Nav
Flight
Planning Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
round Mapping
1) Select the MODE Softkey.
2) Select the GROUND Softkey to place the radar in Ground Map Mode.
3) Select the BACK Softkey.
S
ector Scan
1) While in the Horizontal Scan Mode, move the Joystick right or left to place the Bearing Line in the desired position. The location of the Bearing Line will become the center point of the Sector Scan.
2) Press the FMS Knob to display the cursor.
3) Turn the large FMS Knob to place the cursor in the SECTOR SCAN field.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cockpit Reference Guide for the Cessna Citation Mustang(19)
