PAR T 1 DIRECT DRIVE ENGINES
SECTIONI CCRANKCASE,CRANKSHAFT,CAMSHAFT
Ref. New Ref. Old Chart Nomenclature Dimensions Mfr. Min. Serv. & Max. Max. Clearances Mfr. Min. Serv. & Max. Max.
508 607 ALL Crankshaft Prop. FlangeRun-Out .002 .005
509 941 ALL Starter Ring Gear and Support .014T .022T (A)
510 504 A-B-D-G-J-S-T-Y-AF 504BD-BE Crankshaft TimingGear andCrankshaft .0005T .0010L (A)
511 536 A-B-D-G-J-S-T-Y-AF Tappet Body and Crankcase .0010L .0033L .004L
536 BD-BE Tappet Body and Crankcase .0010L .0030L .004L
A-B O.D. of Tappet .6232 .6240 .6229
B1-D-G-J-S-T-Y-AFB1-D-G-J-S-T-Y-AF O.D. of Tappet .7169 .7177 .7166
O.D. of Tappet .8740 .8745 .8737
A-B I.D. Tappet Bore in Crankcase .6250 .6263 .6266
B1-D-G-J-S-T-Y-AF I.D. Tappet Bore in Crankcase .7187 .7200 .7203
BD-BE I.D. Tappet Bore in Crankcase .8755 .8773 .8776
512 559 B1-D-G-J-S-T-Y Tappet Plunger Assembly and Body -Chilled .0010L .0047L .0067L
S7-S1-AF Tappet Plunger Assembly and Body -Hyperbolic .0010L .0067L .0087L
513 560 B1-D-G-J-S-T-Y Tappet Socket and Body .002L .005L .007L
S7-S1-AF Tappet Socket and Body (Hyperbolic) .002L .007L .009L
514 537 ALL Camshaft and Crankcase .002L .006L
515 538 ALL Camshaft -End Clearance .002L .009L .015L
516 539 ALL Camshaft Run-Out at Center BearingJournal .000 .006
517 578 518 579 All ModelsUsingCounterweights All ModelsUsingCounterweights Counterweight Bushing and Crankshaft Counterweight Roller -End Clearance .0013T .0026T .007L .025L (A) .038L
519 580 All ModelsUsingCounterweights Counterweight and Crankshaft -Side Clearance* .003L .017L
520 696 All Models Using 696Counterweights 521 775 All ModelsUsingCounterweights Counterweight Bore and Washer O.D. I.D. of CounterweightBushing .7485 .7505 .7512 .0002L .0030L (A)
775 * Measure below roller next to flat.
SSP1776 1-3
SERVICE TABLE OF LIMITS
PART 1 DIRECT DRIVE ENGINES
SECTIONI CRANKCASE, CRANKSHAFT,CAMSHAFT
Ref. Ref. Chart Nomenclature Dimensions Clearance
New Old Mfr. Min. Serv. Mfr. Min. Serv.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：Lycoming SERVICE TABLE OF LIMITS AND TORQUE VALUE RECOMMENDATIONS(5)
