Introduction Page 13 Revised: February 28, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF ILLUSTRATIONS
FIGURE NO. SUBJECT GRID NO.
6-1. Three View 1C22
6-2. Station References 1C23
6-3. Access Plates and Panels 1D2
7-1. Jacking 1D9
8-1. Leveling Airplane 1D15
8-2. Weighing 1D17
11-1. Exterior Placards and Markings 1E15
11-2. Interior Placards and Markings 1E17
12-1. Service Points 1F9
12-2. Lubrication Chart - Landing Gear, Main 1F22
12-3. Lubrication Chart - Landing Gear, Nose 1G2
12-4. Lubrication Chart - Control System, Part 1 1G4
12-5. Lubrication Chart - Control System, Part 2 1G6
12-6. Lubrication Chart - Power Plant and Propeller 1G8
12-7. Lubrication Chart - Cabin Door, Baggage Door and Seats 1G10
20-1. Torque Wrench Formula 1G17
20-2. Method of Installing Rod End Bearings 1G18
20-3. Cherrylock Rivet Removal 1G19
20-4. Identification of Aircraft Fluid Lines 1G21
21-1. Cabin Environmental System Installation 1H13
21-2. Heater and Combustion Air Blower Assembly 1H14
21-3. Diagrammatic Cutaway of Heater to Show Whirling Flame Action 1H15
21-4. Fuel Regulator and Shutoff Valve 1H16
21-5. Top View - Duct Switch 1H16
21-6. Intake Valve and Switches 1H17
21-7. Wiring Diagram (Heater) 1H21
21-8. Primary Power Circuit (Heater) 1H22
21-9. Starting Power Circuit (Heater) 1H23
21-10. Spark Plug Fixture (Heater) 1I1
21-11. Wiring - Test Setup (Heater) 1I1
21-12. Spark Plug Gap Adjustment (Heater) 1I2
21-13. Ignition Unit Assembly (Heater) 1I6
21-14. Test Setup for Fuel Regulator and Shutoff Valve (Heater) 1I9
21-15. Heater Fuel Pump 1I10
21-16. Suggested Design for Seal Plates, Plugs, and Caps for
Combustion Tube leakage Test 1I14
21-17. Test Setup for Combustion Air Pressure Switch 1I14
21-18. Exploded View of Heater Assembly 1I19
21-19. Exploded View - Combustion Air Blower and Motor Assembly 1I22
21-20. Suggested Setup of Heater Operation Test 1I24
Introduction Page 14
Revised: February 28, 2002
1A18
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF ILLUSTRATIONS (cont)
FIGURE NO. SUBJECT GRID NO.
21-21. Wiring Connections for Heater Operation Test 1I24
21-22. Spark Plug Gap Adjustment Tool 1J3
21-23. Heater Hourmeter Installation 1J4
24-1. Lamp Bank load 1J24
24-2. Battery Box 1K2
24-3. Electrical Component Location (Lamar Model No. B-00392-1) 1K5
24-4. Lamar B-00392-1 Regulator Overvoltage Test Method 1K6
25-1. Seat Back Lock 1K13
25-2 Lumbar Seat Bladder Installation 1K15
25-3. Artex 110 ELT 1K18
25-4. Artex ELT 110 Wiring Schematic 1K19
27-1. Rod End Bearing Installation 2B8
27-2. Control Cable Inspection Technique 2B9
27-3. Cable Wear Pattern 2B10
27-4. Internal Cable Wear 2B10
27-5. Pulley Wear Patterns 2B12
27-6. Control Column Assembly 2B19
27-7. Flex (Universal) Joint Assembly 2B21
27-8. Aileron Controls 2B23
27-9. Bellcrank Rigging Tool 2C1
27-10. Aileron Rigging 2C2
27-11 Rudder Controls 2C7
27-12. Clamping Rudder Pedals 2C9
27-13 Rudder Rigging Tool 2C9
27-14. Rudder Rigging 2C9
27-15. Rudder Travel Adjustments 2C10
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：西门诺尔飞机维护手册 simenole PA-44-180 AMM 1(5)
