(2)
Remove trim strip at each side of window panel.
(a)
Insert a screwdriver under spring clip retaining top of trim strip and move trim strip down until slot is free of spring clip.
(b)
Slide trim strip down between window panels and remove it at bottom edge of window panels.
(3)
Remove lining fasteners along each side of window panel.
(a)
Rotate quick-release fasteners 90 degrees to release.
(b)
On the upper attachments, turn window panel retainer 90 degrees and remove through gap between window panels.
(c)
On the lower attachments, remove retaining washer and quick-release fastener through gap between window panels.
(4)
Push window panel up into upper trim extrusion until bottom edge of panel is free of carpet riser panel.
(5)
Pull bottom of window panel inboard, then pull down on window panel until top edge is free of upper trim extrusion.
(6)
Support window panel and disconnect electrical plug from window panel light on outboard side of panel.
(7)
Remove window panel.
538
Aug 15/73 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 52-32-81 Page 401
Main Cargo Door Lining Installation 533
52-32-81 Figure 401 (Sheet 1) Nov 15/71
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
533 Main Cargo Door Lining Installation
Nov 15/71 Figure 401 (Sheet 2) 52-32-81
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Main Cargo Door Lining Installation 533
52-32-81 Figure 401 (Sheet 3) Nov 15/71
Page 404
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
B. Remove carpet riser panel.
(1)
Remove cargo handling pallet guide rail and side restraint over carpet riser panel if installed. Refer to Chapter 25, Equipment and Furnishings.
(2)
Pull sidewall carpet section away from tap securing it to carpet riser panels.
(3)
Loosen screws securing adjustable top edge of carpet riser panel and slide top edge down to clear window panel. (See figure 401.)
(4)
Rotate two quick-release fasteners on carpet riser panel 90 degrees to unlock. Also unlock fasteners on adjacent overlapping carpet riser panel.
(5)
Pull inboard on end of panel containing quick-release fasteners, slide opposite end out from under adjacent carpet riser panel, and remove panel.
3. Install Main Cargo Door Lining
A. Install carpet riser panel.
(1)
Slide end of carpet riser panel that does not contain fasteners under adjacent panel and engage angle on outboard side with fire stop panel in sidewall. (See figure 401.)
(2)
Lock quick-release fasteners on carpet riser panel and adjacent panel by rotating 90 degrees.
(3)
Push up adjustable to p edge of carpet riser panel to engage al1 three tabs on window panel and tighten screws to secure top edge.
(4)
Install sidewall carpet section on carpet riser panels by pressing against double-surface tape.
(5)
Reinstall cargo handling pallet guide rail and side restraint if removed. Refer to Chapter 25, Equipment and Furnishings.
533
Nov 15/71 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 52-32-81 Page 405
B. Install sidewall window panel.
(1)
Support window panel adjacent to area in which it is to be installed and connect electrical plug to window panel light on outboard side of panel.
(2)
Push top edge of window panel up into the upper trim extrusion until bottom edge will engage the carpet riser panel. (See figure 401.)
(3)
Push window panel down to align window panel opening with outer window and to engage tabs on bottom edge of window panel with carpet riser panel.
(4)
Check that all three tabs on window panel are engaged with carpet riser panel and adjust riser panel if necessary.
