- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(h) If the resistance test values are out of the specified limits:
- disconnect the HJ11 harness (located at the 6 o'clock junction box) from the CJ11L and do an electrical resistance test through the CJ11L harness between: . pins 5 and 6 (80 to 110 ohms) . pins 2 and 7 (80 to 120 ohms) . pins 3 and 4 (85 to 120 ohms) . pins 5 and 1 (> 10 megohms) . pins 2 and 1 (> 10 megohms) . pins 3 and 1 (> 10 megohms) . pin 5 and the ground (> 10 megohms) . pin 2 and the ground (> 10 megohms) . pin 3 and the ground (> 10 megohms).
F 『 EEFF : ALL E ∞∞75-30-00∞∞∞∞∞∞∞∞∞∞Page 221
E E Aug 01/99 E E ECES
E E 56 E E E (i) If the resistance test values are out of the specified limits:
F 『
E C F M E
E E
- replace the CJ11L harness (Ref. AMM TASK 73-21-50-000-025) and (Ref. AMM TASK 73-21-50-400-025).
(j) If the resistance test values are in the specified limits:
- replace the HJ11 harness (Ref. AMM TASK 73-21-50-000-044) and (Ref. AMM TASK 73-21-50-400-044).
B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞75-30-00∞∞∞∞∞∞∞∞∞∞Page 222
E E Aug 01/99 ERE
ECES E
F 『
E C F M E
E E
E 56 E
E E
TASK 75-30-00-810-814
Loss of the VBV Feedback Signal - Engine 2 - Channel A
1. Possible Causes
_______________
- VBV sensor (RVDT)
- ECU (4000KS)
- harness HJ11
- harness CJ11L
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-50-000-025 Removal of the CJ11L Harness AMM 73-21-50-000-044 Removal of the HJ11 Harness AMM 73-21-50-210-001 Visual Inspection of the Wiring Harness AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses AMM 73-21-50-400-025 Installation of the CJ11L Harness AMM 73-21-50-400-044 Installation of the HJ11 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring) R AMM 75-31-00-200-001 Manual Operation Check of the Variable Bleed Valve R Doors
AMM 75-31-70-000-002 Removal of the Variable Bleed Valve position Sensor AMM 75-31-70-400-002 Installation of the Variable Bleed Valve position Sensor
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. The failure message is generated if the channel A signal is invalid, out of range, or both channels disagree.
(1) If the failure message VBV SNSR, J11, ECU is not confirmed:
(a) No maintenance action is required.
F 『 EEFF : ALL E ∞∞75-30-00∞∞∞∞∞∞∞∞∞∞Page 223
E E Aug 01/05 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
(2) If the failure message VBV SNSR, J11, ECU is not confirmed but is repetitive:
- disconnect the CJ11L harness from the VBV sensor (VBV-A connector) located left core compartment and visually examine the receptacle and the harness for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-001).
(a) If damage is found:
- repair or replace as required.
(b) If no damage is found:
- replace the VBV sensor (RVDT) (Ref. AMM TASK 75-31-70-000-002) and (Ref. AMM TASK 75-31-70-400-002).
NOTE : After new VBV sensor is installed, a rigging of the VBV
____ R system is required (Ref. AMM TASK 75-31-00-200-001).
(c) If the fault continues during the subsequent flights:
- disconnect the HJ11 harness from the ECU (4000KS) and visually examine the receptacle and the connector for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-001).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 大气 AIR(59)
