R (2) Repeat the fault isolation procedure if the fault continues.
F 『
∞∞75-22-00∞∞∞∞∞∞∞∞∞∞Page 238
EEFF : ALL E
E E Aug 01/01
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
TASK 75-22-00-810-809
R Failure of the LPTC Valve on Engine 1
1. Possible Causes
_______________
R - LPTC valve R - HMU R
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R AMM 73-21-10-000-001
R AMM 73-21-10-400-001
R
AMM 73-21-60-000-001
AMM 73-21-60-400-001
AMM 73-29-00-710-040
R AMM 75-22-10-000-001
R
R AMM 75-22-10-400-001
R
R
3. Fault Confirmation__________________
Removal of the Hydromechanical Unit (HMU)
Installation of the Hydromechanical Unit (HMU)
Removal of the Electronic Control Unit (ECU)(4000KS)
Installation of the Electronic Control Unit
(ECU)(4000KS)
Operational Test of the FADEC on the ground (with
Engine Motoring)
Removal of the Low Pressure Turbine Active Clearance
Control Valve (LPTACC).
Installation of the Low Pressure Turbine Active
Clearance Control Valve (LPTACC).
A. Do the operational test of the FADEC 1B on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
NOTE : If ECU 1820M36P02 or 1820M89P02 is installed, the confirmation
____ test is not required.
4. Fault Isolation
_______________
R A. This fault is generated if the actual valve position disagrees with the
R demanded valve position for a set time interval.
R (1) If the failure message LPTC VLV (POS), HMU is not confirmed:
R (a) No maintenance action is required.
F 『
∞∞75-22-00∞∞∞∞∞∞∞∞∞∞Page 239
EEFF : ALL E
E E Feb 01/02
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R (2) If the failure message LPTC VLV (POS), HMU is not confirmed but is
R repetitive:
R NOTE : No maintenance action is required unless the fault becomes too____
R repetitive.
R - do the following steps until the fault is corrected.
R (a) Replace the LPTC valve (Ref. AMM TASK 75-22-10-000-001) and (Ref.
R AMM TASK 75-22-10-400-001).
R (b) If the fault continues during the subsequent flights:
R - replace the HMU (Ref. AMM TASK 73-21-10-000-001) and (Ref. AMM
R TASK 73-21-10-400-001).
R (c) If the fault continues during the subsequent flights:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
R (Ref. AMM TASK 73-21-60-400-001).
R (3) If the failure message LPTC VLV (POS), HMU is confirmed:
R (a) Replace the LPTC valve (Ref. AMM TASK 75-22-10-000-001) and (Ref.
R AMM TASK 75-22-10-400-001).
R (b) If the fault continues:
R - replace the HMU (Ref. AMM TASK 73-21-10-000-001) and (Ref. AMM
R TASK 73-21-10-400-001).
R (c) If the fault continues:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
R (Ref. AMM TASK 73-21-60-400-001).
R
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞75-22-00∞∞∞∞∞∞∞∞∞∞Page 240
E E Feb 01/02 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 75-22-00-810-810
R Failure of the LPTC Valve on Engine 2
1. Possible Causes
_______________
R - LPTC valve R - HMU R
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 大气 AIR(35)
