曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
SHDG2=VOR/LOC
SHDG3=VOR/LOC
SHDG4=ROLLOUT
SALT1=VNAV
SALT2=GS
SALT3=FLARE
SALT4=V/S
Thus, if you wanted to change the anunciator of the Autopilot main mode to A/P from CMD, you would
have to enter:
ACMD1=A/P
ACMD2=F/D
ACMD3=LAND 2
ACMD4=LAND 3
Flap Definition
We have to define proper flap position names in relation to their flap setting in side of FS. This largely
depends on the flight model used and what you want the flap names to be. Here we are chaning an
existing file to accomodate for our flight model's or cockpit's flap positions which we want to be UP - 1 - 5 -
10 - 20 - 25 - 30
In the CDU, please go to INDEX, MAINT, MONITOR, then check the flap settings in the lower right half of
the screen. Please make sure you re-load the aircraft when you make changes to the aircraft configuration
file.
See the value under "CURR.FLAPS" and "FLAP REL. POS" in the right side of the MONITOR page.
You press F5 in FS (flaps up) it will say 0 under curr flaps and 0 () under flap rel pos. The first entry is
what the NAME of the flap setting is, the second is the one retreived from the aircraft configuration table as
a reference, the actual value is in brackets.
flpset (FLAP RELATIVE POSITION) =0 is Flaps UP, = 40 is Flaps Full.
If you press F7 (flaps one notch down) It might say the following (depends on the flight model, here the
default 747-400 in FS2004):
Position
The
actual
flap
sequence
CURR
FLAPS
(flppos)
the text
in the
Glass
Cockpit
FLAP
REL
POS
(flpset)
the
value
from
Comment
Project Magenta Revision: 12 March-08
114
FS
1st notch
(UP) 0 0 () Flaps Up, would display UP in the Glass Cockpit
2nd 1 (!!!) 7 (1)
(!!!)
Here we want the flap text to be 1, and something is undefined in
the configuration file, FS reports a flpset of 1, but 7 is defined and
looked up, the intermediate (1) is missing. We need to insert a flap
block to cover this!
3rd 1 7 (7) Here we would want a flap text of 5, not 1... you see the 1 is
doubled, so something is wrong.
4th 5 13 (13) Here I want a flap text of 10 for instance...
5th 20 27 (27) The rest is OK...
6th 25 33 (33)
7th notch
(FULL) 30 40 (40) 40 is the maximum position, and this should be shown as 40
Current
(please note that the vmax, vret, vext and vmin are
unchanged, refer to the description at the beginning
of the document)
Important: note that there are seven flap positions,
but only 6 blocks of information!
Changed (according to the comments above)
We have to add a block for the flpset 1 and
need to change the entries for the following
flap positions.
flppos=0
flpset=0
vmax=340
vret=0
vext=210
vmin=190
flppos=1
flpset=7
vmax = 227
vret = 180
vext = 180
vmin = 165
flppos=5
flpset=13
vmax = 225
vret = 170
vext = 170
vmin = 160
flppos=0
flpset=0
vmax=340
vret=0
vext=210
vmin=190
flppos=1
flpset=1
vmax = 227
vret = 180
vext = 180
vmin = 165
flppos=5
flpset=7
vmax = 227
vret = 180
vext = 180
vmin = 165
Project Magenta Revision: 12 March-08
115
flppos=20
flpset=27
vmax = 195
vret = 160
vext = 150
vmin = 140
flppos=25
flpset=33
vmax=190
vret=150
vext=140
vmin=135
flppos=30
flpset=40
vmax=190
vret=150
vext=140
vmin=130
flppos=10
flpset=13
vmax = 225
vret = 170
vext = 170
vmin = 160
flppos=20
flpset=27
vmax = 195
vret = 160
vext = 150
vmin = 140
flppos=25
flpset=33
vmax=190
vret=150
vext=140
vmin=135
flppos=30
flpset=40
vmax=190
vret=150
vext=140
vmin=120
Project Magenta Revision: 12 March-08
116
Terrain Data Files
Last Update:
terrain1.zip PAJN, LIRN, LSZH, KLAX, HAAB
terrain2.zip MMAA, MMMX, KSLC, MTPP, KLAS
terrain3.zip LGAV, LFMN, EDDS, LIRF, LEMD
terrain4.zip BGSF, LOWI, LOWS, SKBO, SBSP
terrain5.zip BIRK, ENGM, ESSA, EDDM, CYVR, RJBB
terrain6.zip KDEN, EGPH, , OLBA, VHHH, SPIM, ENBO
terrain7.zip LTBA, KPDX, NWWW, KSFO, LSGG, YSSY
terrain8.zip CYYC, EDDF, MMMY, LIPZ, LIMM, LGZA HTKJ, GMFF, FACT
(just put the .de1 files into the glass cockpit folder and it will move them to the /terrain subfolder. If it is
not there, then that folder will be created)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Project Magenta USER MANUAL Revision: 12 March-08(36)
