曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
21. RADAR WARNING RCVR
a. PWR switch - OFF.
b. DISPLAY TYPE switch -As Desired.
28. ASPJ
a. SYS switch - OFF.
b. BIT switch - OFF.
c. TAC switch -NORM.
29. MFA priority switch -NORM.
30. AN/ALE-39 PWRMODE switch -OFF.
3 1. Data-link panels
a. TEST/NORM&J switch - NORM.
b. FREQ selector - Set.
c. Power switch -OFF.
d. REPLY switch-NORM.
e. MODE switch - TAC/JTlDS (as required).
Note
The data-link MODE switch must be set to
the required link system (JTIDS or TAC) for
appropriate MFD display processing.
f. ADDRESS - Set.
32. APX-76 -OFF.
33. IFF MASTER knob - OFF.
34. MODE 4 switch -Out.
35. IFF ANT switch - DIV.
36. INTERIOR LIGHTS panel -As Desired.
31. RADAR BEACON switch -OFF.
38. RADAR BEACON MODE switch -As Desired.
39. GND CLG switch - OFF.
40. SYS TEST-SYS Pm. ground check panel -
Closed.
41. POWER SYS TEST switch-OFF.
7.5.2 Prestart - RIO. The following checks are
performed by the RIO after starting air and electrical
power are. applied prior to starting engines.
l Starting air, which provides full ECS capability,
must be connected to the aircraft
with elect&al power to cool tempemturecritical
avionics.
l If starting air is not available, a forced-air
gmund cooling unit and servo air must be
connected before turning on avionics
equipment.
l Ifelectricalpowerisnotumneotedwithspare
starikgair,theECSwilIdrivetofullhot.
. To prevent overheating the outboard
spoiler module, pull the OUTBD
SPOILER PUMP circuit breaker (2B3)
anytime external power is connected and
the flaps are extended.
l Failure of the COOLING AIR light to illuminate
on external electrical power indicates
a miswired or failed sensor. The
COOLING AIR light will not be available
to indicate a subsequent ECS turbine
failure.
1. Seat, KS, and U/VI-IF foot switches -Adjust.
Adjust seat height so helmet is beneath the canopy
breaker. Adjust ICS and UBF foot pedal fore-aft
position for sitting comfort.
2. External power and air -ON.
3. ICS - Check
Verify two-way communications between flight
crewmembers and adjust volume to a comfortable
level.
4. DL, JTIDS, tacan, and U/VI-IF - Set.
Set communications/tacan!command control in
accordancew ith mission and flightcrew operating
procedures.
7.29 ORIGINAL
NAVAIR 0%Fi4AAD1
5. Fuel quantity - Check.
6. Lights-Check
Check for illumination of console and instrument
lighting.
7. LTS test-Check
Check that all caution and advisory lights and
E4X lights illuminate.
Note
During pilot INST test, the RIO should observe
fuel counter decreaset o 2,000 pounds
and MASTER CAUTION and FUEL LOW
lights illuminate.
8. Ejection seats -ARMED.
Arm ejection seat by releasing catch and rotating
SAFE/ARMED handle down to ARMED.
9. CANOPY handle -CLOSE.
RIO will normally close canopy. Ensure verbal
clearance from pilot. Check that CANOPY light
goes out with tirll forward transition of canopy into
the sill locks. Check that SEAT UNARMED light
does not illuminate.
1 WARNING 1
Flightcrews shall ensure that hands and foreign
objects are clear of front cockpit handholds,
top of ejection seats, and canopy sills
to prevent personal injury and/or structural
damage during canopy opening or closing
sequence. Only minimum clearance is afforded
when canopy is transiting fore and aft.
Note
If CLOSE does not close the canopy, depress
the grip latch and release and push
handle outboard and forward into BOOST.
If it is necessaryt o use BOOST, the handle
shall be returned to CLOSE to avoid bleed
off of pneumatic pressure.
10. Acknowledge -Ready To Start.
7.5.3 Engine Start - RIO. The RIO must monitor
pilot procedures and plane captain signals to ensure
maximum safety during the engine start sequence.
7.5.4 Poststart - RIO
1. NAV MODE switch - Align.
2. DD power switch -ON.
Failure to tutu DD power on prior to RDR switch
causes a false DD power fault indication in ORT.
3. RDR switch - XMIT.
Verify that the SENSOR COND advisory light
illuminates.
4. RADAR COOLING switch - ON.
Verify that the SENSOR COND advisoty light
goes out.
5. MFD3
a. Power switch - DAY/NIGHT/AUTO.
b. BRIGHTNESS and CONTRAST -Set.
6. DEU -On.
7. MSL PREP switch - As Required.
8. TCS switch - ON.
9. Align coordinates - VerifyQdatc
10. OXYGEN SUPPLY valve-ON.
Turn OXYGEN SUPPLY valve ON, place mask
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
F-14D 飞行手册 Flight Manual 2(30)
