曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
press CLR or ACT key.
REV 56, Jan 31/03
Vol. 1 12--70--10
FLIGHT INSTRUMENTS
Head--Up Guidance System
Flight Crew Operating Manual MASTER
CSP A--013
HGS Control Panel
Figure 12---70---4
Glideslope Reference Line
ACT
STBY
ELV
G/S
FAULT CLR BRT + DIM --
HGS Control Panel (1)
Center Pedestal
Indicates
glideslope angle
selection
(0.00 to --9.99).
“” ” used to indicate
degrees. Decimal
position is
automatic.
--3.00 --3.00
HGS Combiner
Glideslope (G/S) Mode Select
Key
Press G/S to enter glideslope
data. Arrow and CRT line cursor
prompt to indicate entry. Use
keypad to enter 3--digit
glideslope angle. Use ENTER
key to select value for use.
Use CLR key to correct entries.
During G/S data entry,
BRT+ and DIM keys
do not function.
upon airplane
ACT
STBY
ELV
G/S
FAULT CLR BRT + DIM --
HGS Control Panel (1)
Center Pedestal
Indicates
runway elevation
selection in feet
(--9999 to 99999).
Default is last
entry.
ELEV Mode Select
Key
Press ELEV to enter
runway elevation
data. CRT line cursor
prompts to indicate
entry. Use DIM-- key
to enter negative
value. Use keypad to
enter number. Use
ENTER key to select
value for use.
Use CLR key to
correct entries.
Glideslope Angle Readout
Glideslope
Elevation
Runway Symbol
Displayed from 300
to 60 feet AGL.
Position depends
course, airplane
heading, and radio
altitude.
Tic marks indicate
runway aim point.
HGS Combiner
Vol. 1 12--70--11
REV 56, Jan 31/03
FLIGHT INSTRUMENTS
Head--Up Guidance System
Flight Crew Operating Manual
CSP A--013
MASTER
HGS Control Panel <Airplanes equipped with the (--503) HGS Computer>
Figure 12---70---5
Glideslope Reference Line
ACT
STBY
ELV
G/S
FAULT CLR BRT + DIM --
HGS Control Panel (1)
Center Pedestal
--3.00 --3.00
HGS Combiner
Glideslope (G/S) Mode Select
Key
Press G/S to enter glideslope
data. Arrow and CRT line cursor
prompt to indicate entry. Use
keypad to enter 3--digit
glideslope angle. Use ENTER
key to select value for use.
Use CLR key to correct entries.
During G/S data entry,
BRT+ and DIM keys
do not function.
upon airplane
ACT
STBY
ELV
G/S
FAULT CLR BRT + DIM --
HGS Control Panel (1)
Center Pedestal
Indicates
runway elevation
selection in feet
(--9999 to 99999).
Default is last
entry.
ELEV Mode Select
Key
Press ELEV to enter
runway elevation
data. CRT line cursor
prompts to indicate
entry. Use DIM-- key
to enter negative
value. Use keypad to
enter number. Use
ENTER key to select
value for use.
Use CLR key to
correct entries.
Glideslope Angle Readout
Glideslope
Elevation
Runway Symbol
Displayed from 300
to 60 feet AGL.
Position depends
course, airplane
heading, and radio
altitude.
Tic marks indicate
runway aim point.
HGS Combiner
NOTE
The reference glideslope
entry is limited to a range
of --2.00 thru to --6.00.
OutofRngdisplayed if the
entry is not within the range.
Indicates
glideslope angle
selection
(0.00 to --9.99).
“” ” used to indicate
degrees. Decimal
position is
automatic.
REV 56, Jan 31/03
Vol. 1 12--70--12
FLIGHT INSTRUMENTS
Head--Up Guidance System
Flight Crew Operating Manual MASTER
CSP A--013
Head---up Guidance System --- Test Mode Selections
Figure 12---70---6 Sheet 1
RECORDED FAULTS
EXISTING FAULTS
SENSOR DATA
AIRCRAFT IDENTIFICATION
HGS SW P/N
A/C ID #7002
HGS TEST MENU
>
ACT
STBY
ELV
G/S
FAULT CLR BRT + DIM --
1 2 3
4 5 6
7 8 9
ENTER 0 TEST
HGS
Test mode:
Engaged by pressing TEST
key when airplane on the
ground or in flight above 500
feet AGL.
Disengaged by pressing
TEST key again.
Test mode is automatically
disengaged on descent
through 500 feet AGL.
HGS Control Panel (1)
Center Pedestal
HGS Combiner
Pilot’s Windscreen Area
Test sub--modes:
The BRT + and DIM -- keys are
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Bombardier_CRJ_00-Flight_Instruments(22)
