曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Cirrus Design Section 7
SR20 Airplane Description
adjusted through the seat position control located below the forward
edge of the seat cushion. The seat track is angled upward for forward
travel so that shorter people will be positioned slightly higher as they
adjust the seat forward. Recline position is controlled through levers
located on each side of the seat backs. Depressing the recline release
control while there is no pressure on the seat back will return the seat
back to the full up position.
• Caution •
The seat bottoms have an integral aluminum honeycomb core
designed to crush under impact to absorb downward loads. To
avoid crushing this core, do not kneel or stand on the seats.
To position front seat fore and aft:
1. Lift the position control handle.
2. Slide the seat into position.
3. Release the handle and check that the seat is locked in place.
To adjust recline position:
1. Actuate and hold the seat back control lever.
2. Position the seat back to the desired angle.
3. Release the control lever.
Each rear seat consists of a fixed seat bottom, a folding seat back, and
a headrest. The seat backs can be unlatched from inside the baggage
compartment and folded forward to provide a semi-flat surface for
bulky cargo extending forward from the baggage compartment.
To fold seat back forward:
1. From the baggage access, lift the carpet panel at lower aft edge of
seat to reveal the seat back locking pins (attached to lanyards).
2. Remove the locking pins and fold seat forward.
Windshield and Windows
The windshield and side windows are manufactured of acrylic. Use
only clean soft cloths and mild detergent to clean acrylic surfaces.
Refer to Section 8 for detailed cleaning instructions.
March 2010
7-40 Information Manual
Section 7 Cirrus Design
Airplane Description SR20
Cabin Safety Equipment
Passenger Restraints
Integrated seat belt and shoulder harness assemblies with inertia
reels are provided for the pilot and each passenger. The rear seat
belts are attached to fittings on the floorboard and the forward seat
belts are attached to the seat frame. The shoulder harnesses are
attached to inertia reels mounted in the seat back for the front seats
and on the baggage compartment rear bulkhead for the rear seats.
Each harness is attached to the seat belt. The buckle half of each
assembly is on the left-hand side and the link half is on the right-hand
side. The inertia reels allow complete freedom of movement of the
occupant’s upper torso. In the event of a sudden deceleration, the
reels lock automatically to protect the occupants. It is recommended
that the seat belts be stowed in the latched position when not in use.
Serials 1268 through 1540 after SB 2X-25-14 and serials 1541 and
subsequent; An inflatable shoulder harness is integral to each crew
seat harness. The electronic module assembly, mounted below the
cabin floor, contains a crash sensor, battery, and related circuitry to
monitor the deceleration rate of the airplane. In the event of a crash,
the sensor evaluates the crash pulse and sends a signal to an inflator
assembly mounted to the aft seat frame. This signal releases the gas
in the inflator and rapidly inflates the airbag within the shoulder
harness cover, After airbag deployment, the airbag deflates to enable
the pilot/co-pilot to egress the aircraft without obstruction.
The crash sensor’s predetermined deployment threshold does not
allow inadvertent deployment during normal operations, such as hard
landings, strikes on the seat, or random vibration.
• Caution •
No slack may exist between the occupant’s shoulder and
restraint harness shoulder strap.
Stow the seat belts in the latched position when not in use.
To use the restraints:
1. Slip arms behind the harness so that the harness extends over
shoulders.
2. Hold the buckle and firmly insert the link.
March 2010
Information Manual 7-41
Cirrus Design Section 7
SR20 Airplane Description
3. Grasp the seat belt tabs outboard of the link and buckle and pull to
tighten. Buckle should be centered over hips for maximum comfort
and safety.
4. Restraint harnesses should fit snug against the shoulder with the
lap buckle centered and tightened around the hips.
To release the restraints:
1. Grasp the top of the buckle opposite the link and pull outward. The
link will slip free of buckle.
2. Slip arms from behind the harness.
Emergency Egress Hammer
An eight-ounce ball-peen type hammer is located in the center armrest
accessible to either front seat occupant. In the event of a mishap
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
西锐20飞机信息手册CIRRUS DESIGN SR20 AIRPLANE INFORMATION MA(63)
