曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
a hydraulic fluid reservoir, a parking brake valve, a single disc brake
assembly on each main landing gear wheel, and associated hydraulic
plumbing. Braking pressure is initiated by depressing the top half of a
rudder pedal (toe brake). The brakes are plumbed so that depressing
either the pilot’s or copilot’s left or right toe brake will apply the
respective (left or right) main wheel brake. The reservoir is serviced
with Mil-H-5606 hydraulic fluid.
Brake system malfunction or impending brake failure may be indicated
by a gradual decrease in braking action after brake application, noisy
or dragging brakes, soft or spongy pedals, excessive travel, and/or
weak braking action. Should any of these symptoms occur, immediate
maintenance is required. If, during taxi or landing roll, braking action
decreases, let up on the toe brakes and then reapply the brakes with
heavy pressure. If the brakes are spongy or pedal travel increases,
pumping the pedals may build braking pressure.
Refer to Section 10, Safety Information, for Brake System operational
considerations.
June 2007
Information Manual 7-63
Cirrus Design Section 7
SR22 Airplane Description
Parking Brake
• Caution •
Do not pull the PARK BRAKE knob in flight. If a landing is
made with the parking brake valve set, the brakes will maintain
any pressure applied after touchdown.
The main wheel brakes are set for parking by using the PARK BRAKE
knob on the left side of the console near the pilot’s right ankle. Brake
lines from the toe brakes to the main wheel brake calipers are
plumbed through a parking brake valve. For normal operation, the
knob is pushed in. With the knob pushed in, poppets in the valve are
mechanically held open allowing normal brake operation. When the
handle is pulled out, the parking brake valve holds applied brake
pressure, locking the brakes. To apply the parking brake, set the
brakes with the rudder-pedal toe brakes, and then pull the PARK
BRAKE knob aft.
June 2007
7-64 Information Manual
Section 7 Cirrus Design
Airplane Description SR22
Figure 7-12
CALIPER
ASSEMBLY
CALIPER
ASSEMBLY
RUDDER
PEDAL(4)
SR22_FM07_1015
PARKING BRAKE
VALVE
PARKING
BRAKE
KNOB
MASTER CYLINDER(4)
RESERVOIR
MIL-H-5606
FLUID ONLY
ROTOR
(DISK)
ROTOR
(DISK)
Brake System
June 2007
Information Manual 7-65
Cirrus Design Section 7
SR22 Airplane Description
Electrical System
The airplane is equipped with a two-alternator, two-battery, 28-volt
direct current (VDC) electrical system designed to reduce the risk of
electrical system faults. The system provides uninterrupted power for
avionics, flight instrumentation, lighting, and other electrically operated
and controlled systems during normal operation.
Power Generation
Primary power for the SR22 is supplied by a 28-VDC, negative-ground
electrical system. The electrical power generation system consists of
two alternators controlled by a Master Control Unit (MCU) mounted on
the left side of the firewall and two batteries for starting and electrical
power storage.
Alternator 1 (ALT 1) is a gear-driven, internally rectified, 60-amp
alternator mounted on the right front of the engine. Alternator 2 (ALT 2)
is a gear-driven, internally rectified, 20-amp alternator mounted on the
accessory drive at the rear of the engine. ALT 1 is regulated to 28 volts
and ALT 2 is regulated to 28.75 volts. The output from ALT 1 is
connected to the Main Distribution Bus in the MCU through an 80-amp
fuse. The output from ALT 2 is connected to the Essential Distribution
Bus in the MCU through a 40-amp fuse. Both alternators are selfexciting
(not self-starting) and require battery voltage for field
excitation in order to start up - for this reason, the batteries should not
be turned off in flight.
Battery 1 (BAT 1) is an aviation grade 12-cell, lead-acid, 24-volt, 10-
amp-hour battery mounted on the right firewall. BAT 1 is charged from
the Main Distribution Bus in the MCU. Battery 2 (BAT 2) is composed
of two 12-volt, 7-amp-hour, sealed, lead-acid batteries connected in
series to provide 24 volts. Both BAT 2 units are located in a vented,
acid-resistant container mounted behind the aft cabin bulkhead (FS
222) below the parachute canister. BAT 2 is charged from the circuit
breaker panel Essential Bus.
The Master Control Unit (MCU) is located on the left firewall. The MCU
controls ALT 1, ALT 2, starter, landing light, external power, and power
generation functions. In addition to ALT 1 and ALT 2 voltage
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
AIRPLANE INFORMATION MANUAL for the CIRRUS DESIGN SR22(72)
