曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
it up from the cabin sidewall and then unfolding the leaves until they
lock in place. The tables (Figure 7-11) can be stowed by folding the
leaves together, raising them up until parallel with the cabin sidewall,
and then sliding them down into the compartment inside the cabin
sidewall.
An optional left side slimline table may be installed in the cabin sidewall
adjacent to the aft forward-facing seat. The left side table unfolds
and stows in the same manner as the larger tables. An optional right
side table is stowed aft of the left side divider and plugs into the receptacles
in the escape hatch armrest. Both tables are approximately 10
inches (25.4 centimeters) wide.
Pilot’s Manual
7-30 PM-126A
TABLE INSTALLATIONS (TYPICAL)
Figure 7-11
Executive Table Slimline Table
Pilot’s Manual
PM-126A 7-31
CABIN MANAGEMENT SYSTEM
(Aircraft 45-002 thru 45-231, 45-233 thru 45-235)
AUDIO/VIDEO SYSTEMS
The optional audio system consists of a 10 disc CD player, a cassette
player, an audio amplifier, four cabin speakers, sub woofer speaker and
a master control unit for cabin speaker control. The audio system also
includes a passenger distribution system located in the outboard
armrests with headphone jacks, output controls and an audio
headphone set at each passenger seat location.
Power for the audio system is 28-vdc through the 20-amp AUDIO
circuit breaker on the copilot’s circuit breaker panel and through the
20-amp SPKRS circuit breaker on the pilot’s circuit breaker panel.
Electrical power for the optional video monitors is provided by the
5-amp VIDEO circuit breaker on the copilot’s circuit breaker panel.
Cabin Speaker Audio Source
To select a listening source for the cabin speakers, first locate the master
control unit. The master control unit (Figure 7-12) may be located on the
outboard armrest panel at any of the cabin seat positions, but it is
generally located on the right side at the second or third row from the
front. Upon power-up the master control unit will display CABIN on
the master control display.
MASTER CONTROL UNIT
Figure 7-12
Next, depress the MENU button on the master control unit until the
display shows A| CD. When the A| CD symbol is displayed, the CD
player will be selected as the active source for the cabin speakers. To
select a different audio source for the cabin speakers, depress the
SELECT
SELECT
MENU
MUTE
MONITOR
CABIN
SELECT
SELECT
MENU
MUTE
MONITOR
CABIN
Master Control Unit
(Location may vary)
Pilot’s Manual
7-32 PM-126A
SELECT (down arrow) button on the master control unit, the next
audio source A| CASS will be displayed. When A| CASS is displayed, the
cassette player is selected as the active source for the cabin speakers.
For additional cabin speaker audio source choices, continue to depress
the SELECT (down arrow) button or SELECT (up arrow) button until
the desired source is displayed. The master control unit display will
show the cabin speaker source selections as follows:
Cabin Speaker Volume, Bass and Treble Adjustment
Cabin speaker volume is adjusted by first selecting the volume control
by depressing the MENU button on the master control unit until VOL
XX% is displayed (the XX represents a 2 digit number from 01 through
99, a percentage of maximum speaker volume). After VOL XX% is
displayed, increase or decrease cabin speaker volume by depressing
the SELECT up arrow or SELECT down arrow on the master control
unit until the desired volume level is achieved. As the speaker volume
level changes, the master control unit will display a corresponding
VOL % value.
Cabin speaker treble and cabin speaker bass are adjusted in the same
manner that cabin speaker volume is with the exception that BASS %
or TREBLE % is selected with the MENU button, instead of VOL %.
Mute and Monitor Switches - Master Control Unit
To turn the cabin speaker sound OFF, depress the MUTE button on the
master control unit. Depress the MUTE button again to turn the cabin
speaker sound ON. To turn the optional video monitor ON, depress the
MONITOR button on the master control unit. To turn the video OFF, depress
the MONITOR button on the master control unit again.
Video Source Selection
Video signal for the video monitor is selected by depressing the MENU
button on the master control unit until V| VCPis displayed. When V| VCP
is displayed, the video cassette player will be selected as the active
source for the video monitor. To select additional optional video
sources, depress the SELECT down arrow or SELECT up arrow until
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Bombardier_Learjet-Interior_Equipment(11)
