曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
placing the cursor over the mode annunciation, and using the tuning
knobs to step up or down through the available modes.
The ADF operating modes are as follows:
(1) ANT (Antenna) — ADF audio signal only.
(2) ADF — ADF receives signal and calculates the relative
bearing to the station.
(3) BFO (Beat Frequency Oscillator) — ADF adds a beat
frequency oscillator to detect continuous wave (CW)
signals.
(4) Voice — ADF has maximum audio clarity and fidelity,
but no bearing information.
Pilot’s Manual
5-56 PM-132A
TRANSPONDER/TCAS TUNING
Transponder operation is similar to COM and NAV operation in that
depressing a line select key beside the function desired will move the
cursor to that location. Those aircraft without TCAS installed will have
an ATC legend at the top of the transponder window, and those
equipped with TCAS will have ATC/TCAS labeled above the window.
Either transponder 1 or 2 can be selected for use and controlled by
either RMU. A number 1 or 2 will appear in front of the transponder
mode in the ATC window on both RMUs indicating which transponder
has been selected. Transponder side selection is toggled by depressing
the 1/2 key on either RMU with the cursor anywhere within the ATC
window.
The transponder is switched from standby to an operating mode by depressing
the line select key adjacent to the mode line. Once the cursor
has been selected, the mode line select key acts as a toggle to switch the
transponder between the standby mode and the active mode. Once the
transponder is in the ALT ON mode, the mode of operation is changed
using the tuning knobs. The active mode of operation can now be
changed by rotating the concentric tuning knobs. Depressing the ID
button of the RMU will initiate an approximate 18 second IDENT mode
on the transponder. This will also illuminate an ID annunciation along
the top edge of the transponder window. A reply annunciator is located
in the upper right corner of the ATC window.
TCAS
The Traffic Alert and Collision Avoidance System (TCAS) provides the
crew with aural and visual indications of potentially dangerous flight
paths relative to other aircraft in the vicinity. The system uses the transponder
to interrogate other transponder-equipped aircraft and determine
their bearing, range, and altitude, if the intruder has an altitude
encoding transponder in operation. Advisories are issued to the crew
via the airplane Primary Flight Displays (PFDs), audio system and
Multi-Function Displays (MFDs) (traffic map). Two levels of TCAS are
in use today, TCAS I and TCAS II. TCAS II, the standard on the Learjet
40, is the same as TCAS I with the exception of providing Resolution
Advisories (RAs) integrated with the vertical speed indicator on the
PFDs and additional aural commands through the audio system. The
TCAS II system consists of a processor, two bearing antennas, and
associated airplane wiring. System control is through the radio management
units. Power for the TCAS system operation is 28-vdc supplied
through the 5-amp TCAS circuit breaker located on the copilot’s
circuit breaker panel (INSTRUMENT/INDICATIONS group).
Pilot’s Manual
PM-132A 5-57
TCAS OPERATION
The controls and displays are integrated with the Honeywell Primus
1000 system. Controls are through the RMUs and TCAS/annunciator
displays are on the MFD and PFDs and the Resolution Advisories (RA)
are integrated with the vertical speed indicator display on the PFDs.
The TCAS II interrogates other aircraft transponders and analyzes the
replies to determine range and bearing of the intruder. In addition, if
the intruder’s transponder is reporting altitude, the relative altitude is
also determined. If the system predicts that safe boundaries may be violated,
the system issues a Traffic Advisory (TA) which is displayed on
the MFD. Should the TCAS II processor determine that a possible collision
exists, it issues visual and audio advisories to the crew to initiate
appropriate vertical avoidance maneuvers.
If an aircraft has a transponder, but does not have altitude reporting,
the TCAS will depict it on the TA display, but without the altitude information
tag, and without the capability of providing evasive commands.
TCAS II is capable of generating a TA display of traffic from
Mode A transponder-equipped aircraft, and it is also capable of generating
RA signals to avoid Mode C-equipped aircraft. For similar
Mode S-equipped aircraft, the airplane’s TCAS II system coordinates
evasive maneuvers for both aircraft. TCAS I can process transponder
information from other aircraft equipped with Mode A, C, or S transponders,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
BOMBARDIER_Learjet_0-Flight_Controls_and_Avionics(26)
