曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
and
S The indicated airspeed is less than or equal to 163 knots with one or both thrust
levers selected to IDLE
or
S The indicated airspeed is less than or equal to 185 knots with the flaps at less than
5 degrees and one or both thrust levers selected to IDLE.
NOTE
The landing gear horn may be muted with one thrust
lever at IDLE and the landing gear not in the down and
locked position. Refer to Chapter 16, Landing Gear.
The “Too low gear” aural warning is heard if any landing gear is not down and locked
with the radio altitude less than 500 ft AGL and the indicated airspeed at less than 190 knots.
REV 56, Jan 31/03
AURAL/VISUAL INDICATING AND Vol. 1 02--20--26
RECORDING
Engine Indication and Crew Alerting System
Flight Crew Operating Manual MASTER
CSP A--013
P. MENU Page
The MENU page, in conjunction with the EICAS control panel is used to set the N1
bugs on the Primary page and to zero the fuel used indication on the FUEL synoptic
page. The MENU page is divided into two sections: menu section and the confirmation
section. The menu section contains two line items N1 REFERENCE and FUEL USED
RESET. The confirmation section has ACCEPTand CANCEL lines. The UP/DN
buttons on the EICAS control panel (ECP) are used to move a cursor, on the left side of
the page, to a desired line. Th SEL button, on the ECP, is used to select the line item.
If the FMS is not available, the FLIGHT NUMBER line will also be displayed in the
menu section.
The MENU page, in conjunction with the EICAS control panel is used to set the N1
bugs on the Primary page and to zero the fuel used indication on the FUEL synoptic
page. The MENU page is divided into two sections: menu section and the confirmation
section. The menu section contains two line items N1 REFERENCE and FUEL USED
RESET. The confirmation section has ACCEPTand CANCEL lines. The UP/DN
buttons on the EICAS control panel (ECP) are used to move a cursor, on the left side of
the page, to a desired line. Th SEL button, on the ECP, is used to select the line item.
Normally, the FMS is used to program the FLIGHT NUMBER, but if the FMS is not
available, the FLIGHT NUMBER and SET IRS HDG lines will be displayed in the menu
section. The SET POS will appear after the IRS heading has been set. <0025>
The MENU page is divided into two sections: menu section and the confirmation
section. Normally, no line items are displayed in the menu section, but if the FMS is not
available the following items that are normally programmed by the FMS will be
displayed: N1 REFERENCE, FUEL USED RESET, and FLIGHT NUMBER. The MENU
page, in conjunction with the EICAS control panel is then used to select the listed
items. The confirmation section has ACCEPT/CANCEL lines used to accept or cancel
the programing inputs. A cursor on the left side of the page is controlled by the UP/DN
buttons on the EICAS control panel (ECP). The SELECT button on the ECP is used to
select an line item.
The MENU page is divided into two sections: menu section and the confirmation
section. Normally, no line items are displayed in the menu section, but if the FMS is not
available the following items that are normally programmed by the FMS will be
displayed: N1 REFERENCE, FUEL USED RESET, FLIGHT NUMBER and SET IRS
HDG. The SET POS will appear after the IRS heading has been set. The MENU page,
in conjunction with the EICAS control panel is then used to select the listed items. The
confirmation section has ACCEPT/CANCEL lines used to accept or cancel the
programing inputs. A cursor on the left side of the page is controlled by the UP/DN
buttons on the EICAS control panel (ECP). The SELECT button on the ECP is used to
select an line item. <0024><0025><0039><0025><0039><0050>
Vol. 1 02--20--27
REV 56, Jan 31/03
AURAL/VISUAL INDICATING AND
RECORDING
Engine Indication and Crew Alerting System
Flight Crew Operating Manual
CSP A--013
MASTER
Menu Page <0024><0050>
Figure 02---20---10
PROMPT MESSAGE (white)
FLIGHT NUMBER
Used to input the flight
number for display on the
status page (only displayed
if the FMS is not available).
ACCEPT/CANCEL
Editing lines:
Used to insert edits.
into system
or cancel the edit.
Works in conjunction
with the SEL button
on the EICAS control
panel.
Menu Page
FUEL USED RESET Line
Accessed through UP/DN
keys on EICAS control panel.
Cursor will go to ACCEPT line
and prompt message will appear.
SEL switch on EICAS control
panel is used to confirm selection.
CANCEL line used to cancel
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Bombardier_CRJ_00-Aural_Visual_Indicating_and_Recording(10)
